06 Identity & adulteration

How we prove a chromium picolinate lot is the picolinate

Technical document 06 · Reviewed 2026-11-18 · Chromium Picolinate

On this page
  1. The four layers
  2. Chromium, picolinate and the 3:1 ratio
  3. IR, HPLC and why XRD is not the identity test
  4. The adulteration routes
  5. What to write into the specification
  6. What to ask the supplier

A chromium picolinate lot is the picolinate when four things agree: the chromium assay sits at 12.2–12.4% by ICP-OES, the IR spectrum matches the reference, the HPLC picolinate result belongs to the same lot, and the material is the trivalent picolinate complex, not a generic chromium salt or a dye-matched dilution. The chromium figure alone proves the metal; it does not prove the ligand. The picolinate identity is the part a generic chromium supplier cannot answer.

In one line

The chromium assay proves the metal; IR and HPLC prove the picolinate, and the trivalent state rules out the hexavalent form; a dye or a chromium salt can match the colour without matching the identity.

The four layers

Identity layers · what each one proves
LayerQuestionEvidence
ArticleIs the powder the named complex?Specification, CAS, appearance, supplier file
MetalHow much chromium is present?ICP-OES, 12.2–12.4%
LigandIs the picolinate present?IR spectrum, HPLC picolinic acid
State and disclosureIs the chromium trivalent, and is anything else in the drum?Cr(VI) screen where required; carrier and dilution statement

Each layer answers a different question. A laboratory result can close one and leave the others open, which is why a single chromium percentage is not an identity file. The article layer is the paperwork; the other three are the measurements that test the paperwork. The trivalent state is not proved by the chromium assay; it is declared by the article and, where required, tested by a Cr(VI) screen. That is why the screen belongs on the specification as its own line.

Chromium, picolinate and the 3:1 ratio

The pure complex has one chromium atom and three picolinate ligands. Its formula weight is 418.31 and its chromium fraction is 12.43%, so the catalog window of 12.2–12.4% is a narrow band around the theoretical figure. If the only chromium source is the complex, that window corresponds to roughly 98.2–99.8% of the theoretical chromium content.

The stoichiometry is a second, independent check. Convert the chromium result and the picolinic acid result to moles and the ratio should land near 3:1. If the chromium is on target and the ligand is low, suspect a second chromium source. If both are low, suspect a dilution or a carrier. If the ligand is high relative to the chromium, suspect unreacted picolinic acid. The ratio is arithmetic from two results, so both results need the same basis and both need to belong to the same lot.

The certificate in this catalog reports identification by IR and HPLC rather than a numeric ligand assay. That is enough to confirm identity; it is not a replacement for the chromium figure. Ask for the HPLC basis if you need to calculate the ratio.

IR, HPLC and why XRD is not the identity test

IR is the primary ligand test. The spectrum of the complex has bands from the pyridine ring and the carboxylate, and the comparison is against a reference spectrum of chromium picolinate; a chromium chloride, a chromium oxide or a simple blend does not give the same spectrum. HPLC looks at the picolinate from the other side: it can measure free picolinic acid, or total picolinic acid after the complex is released, and the certificate should say which basis was used.

X-ray diffraction is not the identity test here. It can show that the powder is crystalline and can detect a crystalline second phase, but it does not name the ligand; a crystalline chromium salt can produce a pattern too. Use XRD as a crystallinity or polymorph check, not as the proof of picolinate. The direct proof is the IR spectrum plus the HPLC result on the same lot.

The adulteration routes

Substitution routes · what they look like and what catches them
RouteWhat it looks likeWhat catches it
Chromium chloride or another Cr saltChromium assay passes; colour may be paleIR and HPLC; chloride or anion check
Dilution with a carrierChromium below the window; more powder per doseChromium assay, LOD, residue, carrier declaration
Dye to match the purple-red colourColour looks right; chromium may be lowIR, HPLC, dye screen, assay
Unreacted picolinic acidLigand high; chromium lowRatio, HPLC basis, chromium assay
Picolinate blended with a chromium saltChromium on target; ligand lowRatio, IR, HPLC
Polynicotinate sold as picolinateDifferent ligand; chromium often lowerIR, HPLC, label and specification

The dye route is the one that colour alone cannot catch. A pale chromium salt can be tinted to the expected purple-red, and the eye will accept it. The IR spectrum and the HPLC result are the tests that do not depend on appearance. The dilution route is the reverse: the colour may be weak because the powder is 1% picolinate, but if the carrier and the assay are declared, that is a legitimate article rather than a substitution.

What to write into the specification

Write the identity into the specification as a set of lines, not a single word. Name the article: “chromium picolinate (chromium(III) tris(picolinate)), CAS 14639-25-9”. Set the chromium window at 12.2–12.4% by ICP-OES. Require IR and HPLC identification on the lot. Keep LOD ≤0.5%, residue on ignition ≤0.2%, particle size ≥95% through 40 mesh, the heavy-metal panel and the microbiological limits. If a Cr(VI) screen is required, write it as a separate line with its detection limit. If the material is a dilution, add the carrier, the ratio and the chromium assay of the blend.

The clause that is often missing is the one about a second chromium source. A specification that names picolinate but allows “chromium” from any source can be satisfied by a blend. Add: “no chromium source other than chromium picolinate; no added dye or colour.” That sentence is easy to test and hard to misinterpret.

What to ask the supplier

  1. What is the chromium result for this lot, by which method, and what is the release window?
  2. Can you provide the IR spectrum and the HPLC picolinic acid result for this lot, with the HPLC basis stated?
  3. Is the lot the complex, or a blend of picolinate with another chromium source or a carrier?
  4. What is the Cr(VI) result, and what detection limit does the method report?
  5. If the material is diluted, what is the carrier, the ratio and the chromium assay of the blend?

Five answers, all tied to one lot code, are an identity file. A chromium percentage on its own is not. The COA page shows where these lines sit on the certificate; the grade page compares the sources; the chromium picolinate hub carries the specification; the FTIR note and the HPLC note describe the methods.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation