What the COA for chromium picolinate actually contains
The certificate for a chromium picolinate lot reports appearance, chromium by ICP-OES, identification by IR and HPLC, loss on drying, residue on ignition, particle size, the heavy-metal panel and microbiology. Each line carries the method and the release limit, and the batch result belongs beside the limit rather than in place of it. The chromium figure is 12.2–12.4% as elemental Cr; the picolinate identity is a separate line because a chromium number cannot name the ligand.
A chromium assay measures the metal, not the molecule; the certificate has to pair the 12.2–12.4% figure with the picolinate identity, the moisture limit and the release result for that lot.
The certificate as a test report
A useful certificate can be read line by line. For each parameter the reader needs the test, the method and the release limit; the fourth column, the batch result, is the one that belongs to the drum in front of them. A document that reprints the specification in the result column has not reported a lot.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Purple-red to red-brown crystalline powder |
| Chromium (Cr) | ICP-OES | 12.2–12.4% |
| Identification | IR and HPLC | Conforms to reference |
| Loss on drying | Gravimetric | ≤0.5% |
| Residue on ignition | Gravimetric, ignition | ≤0.2% |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The catalog limits above are the release gates. The batch COA is the document that confirms a particular lot against them, and the lot code has to match the certificate, the pack and the retained sample.
What the 12.2–12.4% chromium figure measures
Chromium picolinate is C18H12CrN3O6, formula weight 418.31. The chromium fraction of the pure complex is 12.43%, so the catalog window of 12.2–12.4% spans roughly 98.2–99.8% of the theoretical chromium content. That is a narrow window for an elemental assay, and it is deliberately narrow: at this purity the chromium figure doubles as a check on the complex content.
It is only a check if the identity lines pass. ICP-OES measures total chromium after digestion; it does not see the picolinate ligand, and it cannot tell chromium(III) from chromium(VI). The article is the trivalent complex; the oxidation state is a property of the declared molecule and the route, not a second reading on the same line. Where a customer's specification requires a Cr(VI) result, it is a separate test with its own detection limit. A drum of chromium chloride diluted to 12.3% chromium would satisfy the elemental window and fail the IR and HPLC lines. That is why the certificate needs all three: chromium, identification and the purity limits.
Do not confuse this figure with a compendial assay. A monograph may express the assay as the complex on the dried basis, with a 98.0–102.0% window. The catalog figure is elemental chromium by ICP-OES. Both are legitimate, but they are not the same number and should not share one line.
Release limit versus batch result
The release limit is the boundary the lot was accepted against; the batch result is what the laboratory measured. Both belong on the page, in separate columns, with the method beside them. A result equal to the midpoint of the specification is not a result; it is the gate copied across.
Some lines are one-sided. Loss on drying is a ceiling, residue on ignition is a ceiling, and the heavy-metal and microbiological limits are ceilings. Chromium is a window, and identification is a pass or fail. The certificate should not turn every line into a range simply because the specification has one. A chromium result near the middle of the window and an LOD well below the ceiling tell the reader more than two ticks in a “pass” column.
The same discipline applies to the methods. ICP-OES is not a species-specific method; IR is a comparison against a reference spectrum; HPLC has to state whether it measures free picolinic acid or total picolinic acid after release. A method name without a basis is only half a line.
What moves between batches
The chromium assay moves with the reaction, the crystallisation and the drying step. The window is narrow enough that a drift from the top of the window toward the bottom is worth a conversation even though both results pass; a trend across three lots says more than any single result near an edge. Loss on drying moves with the drying end-point and with the pack; residue on ignition moves with the inorganic content left after ignition, so it is read beside the chromium figure rather than as a purity number.
Colour is the least quantitative line and often the first visible one. The specification allows purple-red to red-brown, so a shade difference alone is not a rejection; a batch record that explains it is better evidence than a photograph. Particle size moves with milling and sieving, and it changes flow and blend behaviour rather than the assay.
When to order an outside test
Order an independent test for a new source, a first shipment into a regulated market, a disputed result, or a form claim that the supplier's own certificate does not prove. The useful panel is not a full repeat of the certificate: ICP-OES for chromium, ICP-MS for the heavy-metal panel, IR and HPLC for the picolinate, and a Cr(VI) screen where the specification calls for one.
Ask the laboratory to report its detection limit for any “not detected” line. A Cr(VI) result without a limit says something about the method, not about the sample. The same applies to dye screens and to the HPLC basis. Chain of custody matters as well: the sample tested should be the sample retained, and the lot code should travel with it.
What to compare between suppliers
Put six lines side by side: the declared species; the chromium result and method; the identity methods and their results; LOD and residue; any dilution, carrier or second chromium source; and lot traceability from certificate to pack. Two quotations that agree on chromium but diverge on the other five are not describing the same powder.
The catalog specification sits on the chromium picolinate product page. The tests that separate the picolinate from a chromium salt are on the identity page; the source comparison is on the grade page; the ICP-OES method is described in the method note; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation