02 Grade comparison

Chromium picolinate, chloride or polynicotinate: choosing a chromium source

Technical document 02 · Reviewed 2026-11-18 · Chromium Picolinate

On this page
  1. The source is the ingredient
  2. Three sources side by side
  3. Solubility, moisture and flow
  4. What the dosage form asks for
  5. What changes when you switch

Chromium picolinate, chromium chloride and chromium polynicotinate are three different label ingredients, not three grades of the same chromium. The picolinate carries 12.2–12.4% elemental chromium, the chloride hexahydrate about 19.5%, and the polynicotinate a supplier-defined figure near 10%. Solubility, moisture behaviour and permitted-market status differ with the compound, so the choice starts with the dosage form and the label, not with the chromium percentage alone.

In one line

The source is part of the label and part of the stability file; switching from picolinate to chloride changes the powder weight, the moisture sensitivity and, in the EU, whether the form is on the permitted list.

The source is the ingredient

Chromium is the nutrient on the panel; the compound is the ingredient on the label. “Chromium 200 µg” does not say which powder was weighed, and the three sources behave differently in a capsule, a stick pack and a drink. The differences that matter at a microgram dose are the chromium fraction, the solubility, the moisture pickup and the regulatory listing of the form.

The fraction sets the powder weight. At 12.3% chromium, 200 µg of chromium is 1.63 mg of picolinate. At 19.5%, the same 200 µg is 1.03 mg of chloride hexahydrate. Both weights are small enough that a manufacturer will usually handle a dilution; the dilution, not the drum, is what the capsule contains.

Three sources side by side

Three chromium sources · content, handling and EU listing
SourceChromium contentSolubilityDry behaviourEU permitted list
Chromium picolinate12.2–12.4% (ICP-OES)Sparingly soluble in waterStable crystalline solid; LOD ≤0.5%Named in Annex II
Chromium(III) chloride hexahydrateAbout 19.5%Freely soluble in waterHygroscopic; needs a moisture-tight packChromium(III) chloride is named
Chromium polynicotinateSupplier-defined; often near 10%Depends on the complex and carrierDepends on the carrierNot named in Annex II

The table is a starting point, not a ranking. A polynicotinate is a family rather than a single formula; the niacin content, the chromium content and the carrier vary by supplier, so the COA has to define the article before a specification can. The picolinate and the chloride are single, named compounds with published formulae, which is why their arithmetic can be written down.

Solubility, moisture and flow

Solubility separates the three more sharply than the chromium figure does. Chromium chloride hexahydrate dissolves freely and gives an acidic solution; it is the easiest source to put into a liquid and the hardest to keep dry. Chromium picolinate is sparingly soluble at neutral pH; it disperses rather than dissolves, which is acceptable in a capsule or a suspension and awkward in a clear drink. Polynicotinate solubility depends on the complex and the carrier, so a supplier's “slightly soluble” statement is not a specification until the method and the lot are named.

Moisture behaviour follows the same pattern. The picolinate is a crystalline solid with a tight LOD limit; the chloride hexahydrate is deliquescent and will pick up water from the air, so an open drum changes weight and flow. The polynicotinate may be blended on a carrier, and the carrier's moisture behaviour can dominate. Particle size is separate from all three: a 40 mesh picolinate and a fine chloride powder will not run the same on a capsule machine.

What the dosage form asks for

For a dry capsule or tablet, the picolinate is the straightforward choice when the label names picolinate: it is a stable solid, it blends with the usual excipients, and a 1% dilution gives a weighable amount. A granulated grade can improve flow without changing the label. The chloride is workable in a dry blend only if the blend and the pack keep water out; the same water affinity that makes it easy to dissolve makes it the less forgiving dry ingredient.

For a powder stick or a drink mix, solubility pushes the other way. The chloride dissolves, but the solution is acidic and the powder picks up water; the picolinate disperses, which may be acceptable in a cloudy format and unacceptable in a clear one. Neither source removes the need to test the finished matrix at its real pH and water activity.

At 1% dilution, a 200 µg chromium dose is about 163 mg of blend. That is a capsule-sized weight, and it shows why the carrier and the uniformity of the dilution matter more than the drum assay. A 0.1% dilution would need more than 1.6 g per dose, which is not a capsule.

What changes when you switch

Write the source into the specification before the assay. A line that says “chromium 12%” could describe a picolinate, a diluted chloride or a blend; a line that says “chromium picolinate, 12.2–12.4% Cr by ICP-OES, identified by IR and HPLC” describes one article. The same rule applies to the polynicotinate: name the complex, the niacin content if it is part of the label, and the carrier.

When the source changes, these lines change with it: the ingredient name on the label; the chromium assay and the powder weight per dose; the solubility and the choice of dosage form; the moisture limit and the pack; the identity methods; the permitted-form check; and the stability protocol. A switch that updates only the purchase order leaves the label and the file describing the old material.

Do not switch to a form that is not on the destination market's permitted list, even if the chromium figure is convenient. Do not switch a label that already names picolinate to chloride without changing the ingredient list and the source declaration. And do not use a polynicotinate as a drop-in picolinate: the complex, the carrier and the chromium content are different articles.

The source comparison continues on the picolinate versus chloride page; the regulatory list is explained on the compliance page and in the Annex II note; the identity tests are on the identity page; the catalog specification sits on the chromium picolinate hub.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation