02.1 Squalane vs squalene

Squalane vs squalene: the saturated and unsaturated forms

Technical document 02.1 · Reviewed 2026-11-20 · Squalane

On this page
  1. The reaction that separates the two
  2. The numbers that move
  3. Reading the difference in a laboratory
  4. Why saturation changes the shelf
  5. Two names, two files
  6. Choosing between them

Squalane is the hydrogenated form of squalene: the same thirty-carbon skeleton, with the six double bonds converted to single bonds. The formula changes from C30H50 to C30H62, the molar mass from 410.72 to 422.81, and the iodine value from a window around 371 to a limit of 1.0. Those numbers, not the appearance of the oil, define which material is in the drum.

In one line

Hydrogenating six double bonds turns squalene into squalane, and that single change moves the iodine value from about 371 to below 1.0, the refractive index down, and the label name to a different ingredient.

The reaction that separates the two

Hydrogenation is a catalytic addition. Squalene is treated with hydrogen over a metal catalyst, usually nickel, at elevated temperature and pressure; each double bond takes up one molecule of hydrogen, and six are needed for a complete conversion. The product is filtered to remove the catalyst and deodorised, and the saturation is what remains.

The reaction does not change the carbon skeleton, only its unsaturation. That is why the two oils are so close in density and feel, and why a buyer cannot tell them apart by looking. It also means the difference is quantitative: iodine value, refractive index and chromatographic retention carry the identification that appearance cannot.

An incomplete reaction leaves a mixture. The iodine value sits between the squalane limit and the squalene window, the chromatogram shows two peaks, and the oil keeps some of the oxidation sensitivity of the unsaturated material. A certificate that reports only an assay and an appearance can hide that state.

The numbers that move

Squalane and squalene: the defining figures
PropertySqualaneSqualene
CAS registry number111-01-3111-02-4
Molecular formulaC30H62C30H50
Molar mass422.81 g/mol410.72 g/mol
Carbon-carbon double bondsNoneSix
Iodine value≤1.0 g I₂/100 g350–380 g I₂/100 g
Refractive index at 20 °C1.450–1.4551.494–1.499
DensityAbout 0.81 g/mLAbout 0.86 g/mL
Catalog assay≥95.0% by GC≥90.0% by GC

The iodine value separates the two by a factor of more than 300. The refractive index and the density follow the same direction, and the assay gates differ because the two products are refined to different targets, not because one is purer in any absolute sense.

Reading the difference in a laboratory

A hydrocarbon has no useful ultraviolet chromophore, so an HPLC method with UV detection is the wrong tool. GC with flame ionisation is the practical separation, and the method should name the column, the oven programme and standards for both oils; the peaks are close enough that a retention time alone is weak evidence.

The iodine value is the release figure that decides the question. A squalane lot at or below 1.0 cannot be squalene, and a squalene lot in the 350–380 window cannot be squalane. Refractometry supports it, because the gap between 1.450–1.455 and 1.494–1.499 is far larger than the repeatability of the instrument. Infrared spectroscopy shows the carbon-carbon double-bond absorption in squalene that is absent from squalane, and an ester carbonyl would point to a different adulterant.

When both are present, GC and the iodine value give an approximate split. A partly hydrogenated oil sits between the endpoints, and the iodine value is the quickest way to place it. Colour tells nothing here.

Why saturation changes the shelf

Autoxidation needs a site to start, and squalene supplies six double bonds plus the allylic positions around them. Oxygen attacks those sites and the first products are hydroperoxides, which are neither volatile nor visible; as they decompose, aldehydes and ketones appear, the odour turns heavier and the peroxide value climbs.

Squalane has no such sites, so the chain reaction has nowhere to begin. It still responds to heat and light — any oil does — and a blend containing an unsaturated oil can oxidise around it, but its own shelf behaviour is far less eventful. That is why the saturated oil is used where a long, unrefrigerated shelf matters.

The formulation consequence follows. A squalene formula needs an antioxidant, a pack that excludes oxygen and a container that excludes light. For squalane, a clean pack, a sensible temperature and a moisture check are the practical controls, and the stability work concentrates on colour, odour and the pack rather than on peroxide value. The squalene stability page sets out the oxidation protocol.

Two names, two files

Squalane and squalene are different ingredient names and cannot be swapped on a label. The CAS number, formula and degree of unsaturation all change, so swapping one for the other at the same weight changes the declared ingredient and the evidence behind it, even though the mass difference is only about 2.9%.

The use then decides the framework. Squalane is mainly a cosmetic ingredient, where the INCI name is Squalane and the cosmetic rules apply; squalene is sold in some markets as a food or supplement oil. The route for the destination and the intended use is confirmed by the buyer's regulatory team. A cosmetic certificate does not establish a food use, and a food certificate does not make the material cosmetic.

Source statements are a third label question. Olive-derived material can carry a source claim where the destination allows it, but the certificate alone does not prove botanical origin; the origin record and the traceability chain do. No disease-related claim is made for either oil on this page.

Choosing between them

Take squalane when the brief asks for a saturated, shelf-stable oil and the label names squalane: a cosmetic base, an emollient, a softgel fill, or an oil blend where resistance to oxidation is the point. Take squalene when the specification and the market file call for the unsaturated oil. Neither is a higher grade of the other.

A switch between them is a new material, not a substitution: new specification, new certificate, new stability work and a new label review. The oils may look the same in the bottle, yet the analytical figures, the way each behaves in air and the regulatory file all move.

The squalane hub carries the saturated specification; the squalene hub carries the unsaturated one; the grades page places this comparison in the wider range; the COA page shows how each line is reported; the identity page gives the tests; the methods section explains the analytical approach; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation