03 Stability

Squalane stability: a saturated oil still has limits

Technical document 03 · Reviewed 2026-11-20 · Squalane

On this page
  1. The sealed pack is the first barrier
  2. Blends and emulsions, where the oil is dispersed
  3. What changes in storage
  4. Designing the study around the pack
  5. What the finished product adds
  6. How the retest period is assigned

Squalane's saturated backbone removes squalene's main failure route — there are no double bonds to take up oxygen — but it does not make the oil immune to storage. Heat, light, moisture and contamination still move colour, odour and the moisture result, and a blend that contains an unsaturated oil can oxidise around it. The shelf life assigned to a lot comes from stability data on the pack and the storage condition actually sold.

In one line

Saturation removes the oxidation chemistry that governs squalene, but heat, light, moisture and a poor seal still decide how long a squalane lot keeps its colour and odour.

The sealed pack is the first barrier

The moisture limit of ≤0.1% is checked at release, and it can move afterwards. Squalane does not dissolve water; water enters as droplets or films during filling, or condenses into a part-used container. The result is haze, a cloudy meniscus or a Karl Fischer figure above the limit, and none of those shows up in the assay.

The amber bottle and the HDPE drum are light and moisture barriers, not guarantees. Keep the closure and the neck clean, keep the headspace small, and write the opening date on the drum. A drum moved out of a cold store should be allowed to equilibrate before it is opened, so that condensation does not form on the oil surface.

Colour and odour are the early indicators. The catalog window runs from colourless to pale yellow, which is wide; a distinct yellow cast or a new odour is worth investigating while the assay and the iodine value still pass. Those two lines describe the molecule, not the freshness of the pack, and they will not report a change that has happened at the surface.

Blends and emulsions, where the oil is dispersed

There is no aqueous solution of squalane to stabilise. The oil is insoluble in water and is used neat, as the oil phase of an emulsion, or as one component of an oil blend, and each of those formats adds a failure route that the neat oil does not have.

In an emulsion the oil is divided into droplets. The interface is where oxygen, metal ions and heat meet the oil, and a metal-sequestering agent can matter as much as the antioxidant. In a blend, the other oils bring their own unsaturation; an oil with a high peroxide value can pull the mixture into oxidation while the squalane itself stays unchanged. The antioxidant, where one is used, should be chosen for the whole oil phase.

Heat is the third factor. A hot-fill step or a pasteurisation hold exposes the oil to temperatures the warehouse never reaches, and a softgel shell can transfer moisture over months even though the fill is anhydrous. Bulk data does not answer a question about a finished format.

What changes in storage

Storage factors for squalane and the control for each
FactorEffect on the oilControl
HeatColour darkens; odour can shiftCool store; short heat exposure
LightAccelerates colour change in clear packsAmber bottle; opaque drum; dark store
OxygenSlow for the saturated oil; faster in an unsaturated blendSmall headspace; sealed pack
Metal ionsCatalyse breakdown at an interfaceStainless-steel contact; avoid iron and copper
MoistureHaze and a rising Karl Fischer figure≤0.1%; dry store; closed pack
ContaminationDust, fibres and odourClean filling; closed pack

The factors interact. A half-empty bottle in a warm, bright room has heat, light and a large oxygen headspace at once, and the colour will move before any instrument result does.

Designing the study around the pack

The pack comes first, then the conditions. A common design uses 25 °C/60% relative humidity for warehouse storage, 30 °C/65% relative humidity for a warmer market, and 40 °C/75% relative humidity as the stress arm, with a light-exposure arm alongside. The stress arm is there to find the failure mode quickly; it does not set the shelf life by itself.

The test panel should cover appearance, colour and odour, assay, refractive index, iodine value, moisture and microbiology. Peroxide value is worth keeping even for a saturated oil: a rising figure is evidence that an unsaturated oil has entered the lot or the blend. Report each result at each time point rather than a single pass statement, and state which pack and which lot family were studied.

Study the pack the customer will receive. A 25 kg drum and a 1 kg bottle differ in headspace, in surface-to-volume ratio and in how often they are opened, and those differences belong in the data rather than in an assumption.

What the finished product adds

A softgel brings the shell into contact with the fill, and the shell can donate or take up moisture. Check the fill's colour, odour and moisture at release and after storage, and inspect the shell for brittleness or leakage. An oil blend needs a compatibility check and an antioxidant plan covering every oil in the phase.

A topical emulsion adds emulsifiers, preservatives and an aqueous phase with its own pH. The oil's own stability is the starting point; the emulsion has to be tested as a product. The formulator decides whether an overage is needed, and that decision belongs with the product's stability data rather than with the ingredient certificate.

How the retest period is assigned

No single shelf-life number is published here. The figure depends on the container, the storage condition and the test panel, so it is assigned pack by pack and recorded in the specification, traceable to the stability file. A number quoted without those three is not a shelf life.

When the retest period ends, re-test the retained sample before extending use. Do not extend by assumption, and do not apply a bulk figure to a repacked bottle or a finished softgel. For the standard packs, see the product hub. The COA page covers release testing, the MOQ page covers pack sizes and lead time, the methods section introduces the analytical tests, and the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation