02 Grade comparison

20%, 50% or 70%: choosing a phosphatidylserine grade

Technical document 02 · Reviewed 2026-11-18 · Phosphatidylserine

On this page
  1. Why there is more than one grade
  2. 20%, 50% and 70% side by side
  3. What the powder does on the line
  4. Matching the grade to the dosage form
  5. How to write a grade specification
  6. When a different grade is the wrong answer

The PS percentage decides how much powder carries a label dose; the source and the carrier decide the allergen declaration, the flow and the regulatory route. The catalog grade is a soy-derived 50% powder at 80 mesh, with 20% and 70% quoted on request. Switching grade changes the dose weight, the capsule size and the specification lines — not only the number in the product name.

In one line

The grade decides how much powder carries the label dose, and the source decides the allergen and the regulatory route.

Why there is more than one grade

Phosphatidylserine is concentrated from lecithin, and the concentration step can stop at different PS levels. A 20% powder carries more non-PS solids per gram; a 50% powder is the middle of the commercial range and the grade this catalog lists; a 70% powder carries less material per gram of PS. Each is a different powder with a different mass balance.

Source is a second axis. Soy and sunflower PS can be produced at the same PS content and still differ in fatty acid profile, allergen declaration and regulatory route. Grade and source are often quoted together — “soy-derived 50% powder” — because a change in either one changes the product. The soy versus sunflower page covers the source decision; this page covers the concentration.

20%, 50% and 70% side by side

What changes across phosphatidylserine grades
Line20% grade50% grade (catalog)70% grade
PS content20% nominal; range agreed in the specification50.0–55.0% by HPLC-ELSD70% nominal; range agreed in the specification
Powder per 100 mg PS500 mg200 mg143 mg
Balance of the powderMore non-PS solidsOther phospholipids plus any declared carrierFewer non-PS solids
Typical formatSticks, drink mixes, blendsCapsules, tablets, sticksCapsules, compact sticks
Flow and bulkUsually freer-flowingConfirm bulk density and flowMore cohesive; confirm flow
SpecificationWritten for the gradeWritten for the gradeWritten for the grade

The arithmetic is the first thing to check. A formula that declares 100 mg PS per capsule needs 500 mg of a 20% powder, 200 mg of a 50% powder or about 143 mg of a 70% powder. At 300 mg PS the weights become 1,500 mg, 600 mg and 429 mg. The 20% grade may not fit a small capsule at all, while the 70% grade may leave little room for other actives in a fixed-weight stick.

The second check is the label. The carrier and the other phospholipids are ingredients and have to be declared. A grade with more carrier per gram of PS puts more of that carrier into every dose. If the label claim is built around powder weight rather than PS weight, a grade change can move the declared PS without changing the capsule weight.

The third check is oxidation. Peroxide value is measured on the powder, so the result belongs to the grade and the lot, not to the PS molecule alone. A 20% grade carries more powder per milligram of PS; a 70% grade carries less. When comparing certificates, compare the peroxide value per gram of PS as well as per kilogram of powder, and ask for the value on the lot you will receive.

What the powder does on the line

Particle size is specified as at least 95% through 80 mesh, and that line travels with the grade. A finer cut disperses faster and dusts more; a coarser cut flows better but can settle in a stick. Granulation is available on request and changes the flow, the bulk density and the dispersion, so a granulated grade needs its own specification rather than a note on the milled one.

Higher PS content means a higher phospholipid fraction, and phospholipids are cohesive and hygroscopic. A 70% powder can cake faster than a 20% powder in an open room and can be harder to empty from a hopper. A 20% powder on a free-flowing carrier can be denser and easier to handle but adds mass to every dose. Ask for bulk density, flow and loss on drying on the grade you are buying.

PS is dispersible in water, not soluble. In a stick or drink mix it clouds the liquid, so a clear beverage is not the right format for any grade. In a capsule or tablet the powder is shielded from water, and the grade question becomes fill weight and flow.

Matching the grade to the dosage form

Capsules and tablets usually take the 50% grade because 200 mg of powder for a 100 mg PS claim fits a size 1 or 0 capsule, with room for a flow agent. A 70% grade can shrink the capsule further or leave room for a second active; a 20% grade may need two capsules and is usually a poor fit for a compact dose form.

Sticks and drink mixes can take the 20% grade when powder weight is not the constraint. The 50% grade is also workable if the stick weight allows 200 mg per 100 mg PS. Gummies and chews are limited by water activity and heat rather than by grade alone; the powder has to be added where the matrix is cool enough, and its flow and particle size affect dispersion.

Add an overage only with data. PS is not a crystalline material that sits unchanged in a finished product; heat, moisture and oxygen move the assay and the peroxide value. The overage belongs in the formula specification and the stability study, not in a rule of thumb copied from another ingredient.

How to write a grade specification

Write the grade as a full identity: “Phosphatidylserine 50% powder, soy-derived, 50.0–55.0% by HPLC-ELSD, ≥95% through 80 mesh, loss on drying ≤5.0%, peroxide value ≤10 meq/kg, acid value reported, heavy metals and microbiology as listed, carrier declared if present, source and allergen statement attached.” A 20% or 70% grade gets its own PS range, mesh and peroxide limit where the process supports one; do not copy the 50% limits across.

Name the method and the standard, not only the percentage. The PS result depends on the HPLC-ELSD calibration and on the integration of the phospholipid peaks, so “50% by HPLC” without the detector and standard is not comparable with another supplier's. The COA page sets out the lines a certificate carries; the identity page explains why the profile matters as much as the assay.

Ask for the certificate on the exact grade and lot. A 50% certificate does not describe a 70% powder.

When a different grade is the wrong answer

If the formula needs a clear solution, no PS grade will deliver it; the ingredient is a dispersed lipid. If the label needs a soy-free claim, changing the percentage does not help — the source has to change, and the regulatory route has to be rechecked. If the capsule is already at its fill limit, a lower grade makes the problem worse.

The catalog specification, pack sizes and MOQ are on the phosphatidylserine product page. Oxidation is covered on the stability page, the ordering unit on the MOQ page, and mesh size in the particle-size glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation