03 Stability

Microencapsulated MCT is stable, but the carrier and moisture decide the rest

Technical document 03 · Reviewed 2026-11-19 · MCT Powder

On this page
  1. The dry powder: moisture comes first
  2. Once dispersed: the oil is exposed
  3. Five factors that move the shelf life
  4. A stability protocol that answers the question
  5. The formula around the powder
  6. What shelf life can be supported

Microencapsulation puts a starch wall between the oil and the air, and that wall is why MCT oil can be handled as a free-flowing powder. It is not a seal. Moisture softens the wall, heat speeds oxidation and the pack decides how much water and oxygen reach the powder. The catalog limits of moisture ≤5.0% and PV ≤1.0 meq/kg are release gates; a shelf life has to be supported by stability data on the lot and the pack, not inferred from those two lines.

In one line

The wall slows oxidation and water uptake; the carrier, the moisture and the pack decide whether the powder is still free-flowing at the end of its shelf life.

The dry powder: moisture comes first

Modified starch is hygroscopic. In a sealed pouch the powder equilibrates with the headspace; once the pouch is opened, it equilibrates with the room. Water acts as a plasticiser: it lowers the glass transition of the starch wall, makes the particles stick and turns a free-flowing powder into a caked one. The 40 mesh result at release says nothing about the mesh after a week in an open bag.

The moisture limit of 5.0% is a ceiling, not a target. A lot at 4.5% has little headroom for a humid filling room; a lot at 2% has more. Ask for the moisture result on the lot, the packing humidity and the pouch specification. A foil pouch with a sealed seam is a different barrier from a metallised film or a paper bag, and the pack belongs in the stability case.

Clumping is the visible failure. The earlier signal is a rise in moisture and a drop in flow. If the powder is blended with other hygroscopic ingredients, the blend's water activity matters more than the MCT powder alone.

Once dispersed: the oil is exposed

The powder is dispersible, not soluble. In water, the starch wall hydrates and the oil droplets are released into the continuous phase. From that moment the oil has a large surface area and much less protection than it had in the dry particle. Shear, warm water, a hold tank and a high-speed mixer all shorten the window.

For a beverage, mix close to the point of filling, keep the slurry cool and do not hold it for a long shift. For a dry blend that is reconstituted by the consumer, the finished powder's moisture and the sachet barrier decide the shelf life; the consumer's water is only the last step. Taste is the practical test: an oxidized oil shows up as a stale or off note before a PV result is available.

Five factors that move the shelf life

What drives MCT powder degradation · effect and control
FactorWhat it doesWhat to control
OxygenReacts with surface oil; PV risesBarrier pouch, sealed drum, low headspace
HeatSpeeds oxidation and moisture migrationCool storage, short warm exposure
LightCan accelerate rancidity in exposed oilOpaque pack, dark store
MoisturePlasticises the wall; caking and flow lossMoisture limit, dry room, sealed pack
Trace metalsCatalyse oxidation at low levelsHeavy-metal panel; avoid reactive contact

Surface oil is the common path through all five. The oil at the particle surface has no starch wall over it, so it meets oxygen first. A higher oil load usually means more surface oil, which is one reason a 70% grade needs a tighter process and a better pack than the 50% grade.

A stability protocol that answers the question

Run the powder in the pack it will be sold in. A protocol that tests loose powder in a glass jar answers a different question. The useful design is a baseline plus 1, 3, 6 and 12 months at 25 °C/60% RH, with an accelerated arm at 40 °C/75% RH for early signal. If the market is tropical, add a 30 °C/75% RH arm.

At each point, test moisture, PV, appearance, flow or sieve, and the microbiology set. Add a sensory check and a free-oil or surface-oil figure if the application is flavour-sensitive. Keep a retained sample from the same lot and store it beside the test samples. The result is a curve, not a pass or fail at one point; the shelf life is the point where the curve still meets the specification with a margin.

Accelerated data is a screening tool. A powder that passes 40 °C/75% RH for three months has useful evidence, but the labelled shelf life should rest on real-time data at the declared storage condition.

The formula around the powder

The powder is rarely alone. A stick may also contain a protein, a mineral salt, an acidulant and a flavour. Each of those changes the water activity and the local chemistry. An acidic component can lower pH and change the starch wall; a mineral salt can bring trace metals into contact with the oil; a hygroscopic sweetener can pull water from the MCT particles or release it to them.

If the grade contains an antioxidant, it should be declared, with its name and level. The catalog specification names modified starch as the carrier; any additional processing aid or antioxidant belongs on the technical data sheet and the label. A buyer should not assume protection that is not in the specification.

What shelf life can be supported

The shelf life is the period the supplier can support with data for the material in its pack. Ask for the figure, the storage condition and the test panel behind it. A shelf-life date on a drum is not the same as a stability study, and a study on a different oil load or carrier is not transferable.

Store the powder cool, dry and sealed, away from strong odours. Once a pouch is opened, reseal it, keep it dry and use it within the working period the supplier states.

The COA page explains the release limits; the MOQ page covers the pack sizes; the compliance page covers the document file. The loss-on-drying glossary entry explains why the moisture basis matters, and the grade page sets out the oil load options.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation