How we prove an MCT lot is the declared C8/C10 profile
An MCT lot is the declared material when four things line up: the oil is a triglyceride mixture with the declared C8/C10 profile, the powder carries the declared oil load, the carrier is the declared modified starch and the lot is not oxidized. The GC profile is the centre of that case, but it is not the whole case. GC describes the oil that was extracted; it does not say how much oil the powder contains, and it does not identify the carrier.
Identity is the C8/C10 profile, the oil load, the carrier and the oxidation state read together; a single “MCT” line proves none of them.
Four layers of identity
A certificate that reports only “MCT oil 50%” leaves three questions open. The four layers below close them, and each layer needs its own test or document.
| Layer | Test or document | What it proves |
|---|---|---|
| Oil identity | Specification, source statement, CAS 73398-61-5 | A medium-chain triglyceride oil of the declared source |
| Fatty-acid profile | GC of the extracted oil, C8 and C10 separately | The declared C8/C10 range and ratio |
| Oil load | Extraction and gravimetry | The declared amount of oil in the powder |
| Carrier and condition | Starch identification, moisture, PV, mesh | The matrix is as declared and the lot is not oxidized |
The order matters. A GC profile on a sample of oil proves the oil; it does not prove that the powder contains 50% of it. An oil load without a profile proves the amount but not the identity of the oil. The two tests are complementary, and a supplier should be able to show both on the same lot.
The C8/C10 ratio is the fingerprint
The catalog ranges are C8 55.0–65.0% and C10 35.0–45.0% of the oil. At the edges, the ratio runs from about 1.2:1 to about 1.9:1; the midpoint is 60:40. Both edges are inside the specification, so the ratio is a window, not a single number. A buyer who needs a tighter window, for a label statement or a sensory target, should write it as a separate line rather than assume the catalog range delivers it.
The oil is not only C8 and C10. The balance is other fatty acids, and the GC report should show them if the buyer needs to see the whole picture. A C8-enriched oil made by adding pure C8 is a different specification, not automatically an adulteration, but it will sit at the top of the C8 range and the bottom of the C10 range. The certificate should say what was done, not only the final percentage.
The source oil does not fix the ratio by itself. Coconut oil and palm kernel oil are both raw materials for MCT, and the fractionation cut decides the C8/C10 split. That is why the ratio belongs in the specification as a range, and why a source change that is not written into the specification is a material change.
Why XRD is not the identity test here
X-ray diffraction identifies crystalline phases. In a powder it can show whether the starch carrier is crystalline or amorphous, and it can detect a crystalline mineral filler. It cannot distinguish C8 from C10, and it cannot measure the oil load. For an MCT powder, XRD is a useful check on the carrier and on foreign crystalline material, not a test of the oil's identity.
The identity test for the oil is GC. The identity test for the carrier is a starch identification, supported by the specification. The identity test for the load is extraction and gravimetry. A supplier who offers an XRD pattern as proof of MCT identity has answered a different question.
Adulteration patterns
The common substitutions are not exotic. They are a different oil, less oil, older oil and a shifted profile.
| Pattern | What it looks like | Test or check |
|---|---|---|
| Source oil | Palm kernel or another oil in place of the declared source | Full GC profile; fatty acids outside the C8/C10 window |
| Low oil load | More carrier, a 50% claim on a 40% powder | Extraction and gravimetry on the same lot |
| Oxidized oil | A clean profile with a high PV or a stale odour | PV by a named method, sensory check, date of analysis |
| Shifted profile | C8 added or a C10-rich fraction used | C8 and C10 separately, ratio, full chromatogram |
A fifth pattern is a carrier substitution: maltodextrin or a different starch in place of the declared modified starch. It shows up in the starch identification and in the mass balance, and it matters for the label and for the allergen review.
How to write identity into the specification
The specification should define the oil, the load and the matrix in lines that can be tested. A line that says “MCT powder” without a C8/C10 range and an oil load is a category, not a specification.
| Line | What to write |
|---|---|
| Oil identity | Medium-chain triglycerides, CAS 73398-61-5, source stated |
| C8 | 55.0–65.0% of oil by GC |
| C10 | 35.0–45.0% of oil by GC |
| Oil load | ≥50.0% by extraction |
| Carrier | Modified starch, type declared |
| Oxidation and moisture | PV ≤1.0 meq/kg; moisture ≤5.0% |
| Particle size | ≥95% through 40 mesh |
The lines work as a set. If the oil load moves, the C8 and C10 figures on the powder move with it. If the carrier changes, the starch identification and the label change. If the source changes, the allergen file and the ratio may change. A specification that controls only the oil load leaves the other three layers open.
Five questions for the supplier
- What are the C8 and C10 results on the lot, calculated on the oil, and can you send the chromatogram?
- What is the oil load by extraction on the same lot, and which method was used?
- Which modified starch is the carrier, and what is its inclusion rate?
- What are the PV, the date of analysis and the storage history of the lot?
- If the oil source or the fractionation changes, what notice and what new COA will the buyer receive?
The answers should line up with the COA. A supplier who can answer the profile but not the load has described an oil, not a powder. A supplier who can answer the load but not the carrier has described a number, not a material.
The product page carries the catalog specification; the COA page explains how the profile and the load are reported; the grade page compares the oil loads. The C8 vs C10 page covers the ratio, and the specification glossary entry defines the document.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation