02 Grade comparison

50% or 70% MCT powder: choosing an oil load

Technical document 02 · Reviewed 2026-11-19 · MCT Powder

On this page
  1. Why the oil load is a separate decision
  2. 50% and 70% side by side
  3. What the load does to the powder
  4. The arithmetic on the label
  5. Writing the load into the specification
  6. When the higher load is not the answer

MCT powder is sold by oil load, and the load is the first choice a buyer has to make. A 50% grade carries at least half its weight as MCT oil dispersed in a modified starch matrix; a 70% grade carries more oil and less carrier. Both can be specified with the same C8/C10 ranges because that profile belongs to the oil, but the powder around the oil changes: the weight per dose, the flow, the surface oil and the label arithmetic all move with the load.

In one line

The oil load sets how much powder delivers a gram of MCT; the C8/C10 ranges stay with the oil, but the carrier, the flow and the oxidation exposure change with the load.

Why the oil load is a separate decision

Oil load is not purity. A 50% powder is not half-strength MCT in the sense that a 70% powder is a better material; it is a different balance between oil and carrier. The load sets the mass of powder needed for a declared amount of MCT, the amount of starch that reaches the label, the surface area of oil exposed to oxygen and the way the powder flows and disperses.

The catalog grade is the 50% powder. A 70% grade is available on request and is quoted against its own specification, not against the 50% certificate. Agglomerated versions are also made on request; agglomeration changes particle size and flow, not the oil load. A buyer who needs 70% should ask for that grade's oil load, moisture, PV and particle-size limits and keep them as a separate file.

50% and 70% side by side

Oil load options · what changes between a 50% and a 70% MCT powder at the same oil profile
Line50% catalog grade70% grade, on request
MCT oil≥50.0%About 70%
CarrierBalance, mainly modified starchLess carrier per gram
C8 per gram275–325 mg385–455 mg
C10 per gram175–225 mg245–315 mg
Powder per 1 g oil2.0 gAbout 1.43 g
Flow and dispersionEasier to dry and blendMore surface oil; tighter process
Typical useSticks, capsules, blendsConcentrated blends, smaller doses

The milligram figures are arithmetic from the oil load and the C8/C10 range, not a second specification. They show why two powders cannot be compared by weight alone: a 3 g stick of the 50% grade carries about 1.5 g of oil, while the same 3 g of a 70% grade carries about 2.1 g. The C8 and C10 figures scale with the oil, not with the total powder weight.

What the load does to the powder

Surface oil is the part that matters. At a higher load, the emulsion has more oil to stabilise, the droplet size is harder to hold and more oil sits at the surface. Surface oil meets oxygen first; it also makes the powder tacky, reduces flow and can cause ringing or a heavier mouthfeel in a drink. A 50% grade is more forgiving in a simple blender; a 70% grade may need agglomeration or a tighter dryer recipe to reach the same 40 mesh result.

The catalog grade targets ≥95% through 40 mesh. A 70% grade should carry its own mesh line, because the higher load can change the particle surface. The sieve result describes the particle, not the oil load; a 70% powder can pass the same sieve and still flow differently. The powder is dispersible, not soluble: in water the starch wall hydrates and the oil is released as droplets. A higher load leaves less starch to hold the dispersion, so the same mixing time may not give the same appearance.

The arithmetic on the label

At 50%, 2 g of powder delivers 1 g of oil. A 500 mg capsule holds 250 mg of oil; a 1 g stick holds 500 mg; a 3 g stick holds 1.5 g. At 70%, 1.43 g of powder delivers 1 g of oil, so a 500 mg capsule holds 350 mg and a 3 g stick holds 2.1 g. These are oil figures; the C8 and C10 figures are 55–65% and 35–45% of the oil figure.

If the label declares MCT oil per serving, the powder weight is the declared amount divided by the oil load. If it declares C8 and C10 separately, multiply again by the fatty-acid result. Use the release floor, not the midpoint, so the label remains true across lots. In the EU the nutrition declaration carries fat and saturates, and the modified starch adds carbohydrate; in the US the panel is Nutrition Facts or Supplement Facts, depending on the product type.

The C8/C10 split is not a separate nutrition line in either market. It belongs in the ingredient description, on the specification or on a technical page, not in the nutrition panel. That is another reason to write the load and the profile separately: one drives the label weight, the other describes the oil.

Writing the load into the specification

A load absent from the specification is not controlled. The specification should put the oil load, fatty-acid basis and carrier in lines that can be tested together.

Specification lines that fix the oil load and the profile
ItemWhat to specifyEffect
Oil loadMCT oil ≥50.0% (70% grade: about 70%)Sets the powder weight per dose
C855.0–65.0% of oil by GCFixes the profile, not the powder
C1035.0–45.0% of oil by GCCompletes the declared ratio
CarrierModified starch, type declaredExplains the balance and the label
Moisture and PV≤5.0%; ≤1.0 meq/kgProtects flow and flavour
Particle size≥95% through 40 meshSets the physical form

For a 70% grade, do not copy the 50% sheet and change one number. The higher load changes the surface oil, the drying window and the moisture pick-up, so the 70% grade needs its own moisture, PV, mesh and stability data. The C8/C10 ranges can stay the same because they describe the oil, but the batch COA has to be issued against the grade that was made.

When the higher load is not the answer

A higher load is not automatically right. If the formula needs a free-flowing powder at a high inclusion rate, the 50% grade gives the blender more carrier and less surface oil. If the formula has little room for carrier, the 70% grade helps; if the carrier is part of the texture or the dispersion, the 50% grade may be easier to use. If the pack is a small stick and the dose is modest, the 50% grade may already fit.

The 70% grade earns its place when the dose per gram has to be higher, when the capsule or sachet has a fixed fill weight, or when the formula has no room for the extra starch. Neither grade is better in general; the load is a fit question. The product page carries the catalog specification, the COA page explains how the load and the profile are reported, and the C8 vs C10 page covers the ratio itself. The stability page explains why the higher load needs a tighter pack.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation