02.1 C8 vs C10

C8 vs C10: what the MCT profile changes

Technical document 02.1 · Reviewed 2026-11-19 · MCT Powder

On this page
  1. Two fatty acids, two carbons apart
  2. What the ratio means in the oil
  3. What the ratio means in the powder
  4. The format follows the oil
  5. What goes on the label
  6. The regulatory status does not change
  7. When to choose which

C8 and C10 are the two fatty acids that make up commercial MCT oil, and the ratio between them is a specification choice, not a quality grade. C8 (caprylic acid) has eight carbons; C10 (capric acid) has ten. The catalog profile is C8 55.0–65.0% and C10 35.0–45.0% of the oil by GC, which puts the C8:C10 ratio between about 1.2:1 and 1.9:1. That window, and the oil load behind it, is what a buyer should compare.

In one line

C8 and C10 differ by two carbons; the ratio changes the oil's physical behaviour and the label arithmetic, not the legal status of the ingredient.

Two fatty acids, two carbons apart

Both are saturated medium-chain fatty acids. The two-carbon difference changes the molecular weight, the melting point and the way the triglyceride behaves in an emulsion. The table gives the free fatty acid values; in the oil, the acids are esterified to glycerol, so the oil's melting and flow behaviour is not the same as the pure acid.

C8 and C10 · the two fatty acids in the MCT profile
PropertyC8 · caprylic acidC10 · capric acid
Chain length8 carbons10 carbons
FormulaC8H16O2C10H20O2
Molecular weight144.21 g/mol172.26 g/mol
Melting pointAbout 16.7 °CAbout 31.6 °C
Behaviour in the oilLower viscosity, lower meltingHigher viscosity, more body

The oil is a mixture of triglycerides, not a blend of free acids. The mixed triglycerides keep the oil liquid at room temperature, while the pure C10 acid is solid at that temperature. That is why the ratio and the triglyceride structure both matter, and why the GC profile is reported as fatty acids rather than as a single melting point.

What the ratio means in the oil

The catalog range is a window, not a single ratio. At C8 55% and C10 45%, the ratio is 1.22:1; at C8 65% and C10 35%, it is 1.86:1. The midpoint is 60:40, which is the ratio many buyers write into a specification when they want a consistent sensory and physical profile. The two lines are separate limits, so a lot can sit at either edge and still pass. A buyer who needs a tighter window should write the ratio itself as a line.

Source and fractionation both move the result. Coconut and palm kernel oils are the usual raw materials; the fractionation cut, not the botanical source alone, sets the final ratio. A change of source or cut can move the ratio without moving the oil load, which is why the COA should report C8 and C10 separately rather than a single “MCT” figure.

The ratio is not a purity measure. Both a 55:45 and a 65:35 oil can meet the same MCT specification; the difference is which fatty acids the fractionation collected. The balance is other fatty acids, and the full GC profile is the way to see them.

What the ratio means in the powder

The oil load converts the ratio into a powder-basis figure. At 50% oil, the powder carries 27.5–32.5% C8 and 17.5–22.5% C10. At 70% oil, the same profile gives 38.5–45.5% C8 and 24.5–31.5% C10. A label that declares C8 or C10 per gram needs the powder-basis figure; the oil figure overstates what the serving contains.

C8 and C10 in the powder · 50% and 70% oil load at the catalog profile
Fatty acid50% oil powder70% oil powder
C827.5–32.5%38.5–45.5%
C1017.5–22.5%24.5–31.5%
Oil per gram0.50 g0.70 g

The calculation is simple but easy to skip. Two powders can declare the same 60:40 ratio and deliver different milligrams per gram because their oil loads differ. The ratio describes the oil; the load describes the powder. A specification needs both lines, and a label needs the product of the two.

The format follows the oil

A C8-rich oil is less viscous and has a lower melting range; a C10-rich oil is more viscous and carries more body. In the powder, that shows up in the emulsion, the surface oil, the flow and the way the powder disperses. A C8-rich oil can be easier to emulsify at a given solids level; a C10-rich oil may need more shear or a different carrier balance to reach the same droplet size.

Those differences are physical, not a ranking. A C8-rich powder can feel lighter in a drink; a C10-rich powder can give a fuller mouthfeel. Agglomeration can fix flow, but it does not change the ratio. The 40 mesh target is a particle-size line, not an oil-profile line, and a powder can pass the sieve with either ratio.

What goes on the label

The label describes the oil, not the ratio as a nutrient. In the EU, the nutrition declaration carries fat and saturates; in the US, total fat and saturated fat. C8 and C10 are saturated fatty acids, so they sit inside those lines. Neither market requires a separate C8 or C10 nutrition declaration. The ratio can appear in the ingredient description, for example “MCT oil (C8/C10),” or in a specification, if the statement is truthful and not a health claim.

Keep the oil load and the ratio separate on the label. A front-of-pack “60% C8” statement is a composition statement; it should be supported by the lot data and should not imply an outcome. The ingredient name should match the source and the form, and the carrier should be declared as the carrier.

The regulatory status does not change

Both C8 and C10 are saturated fatty acids, and MCT oil is the ingredient; there is no separate additive approval for a 60:40 oil versus a 55:45 oil. The source oil still drives the allergen file, and the carrier still needs its own status. A ratio statement is a specification or a compositional claim, not a permitted health claim.

That is why the ratio belongs in the technical file and the purchase specification, not in the claims column. It can be checked by GC, it can be declared on the COA, and it can be compared between suppliers. It cannot carry a physiological promise on its own.

When to choose which

Choose on the physical and label consequences. A C8-rich profile gives a less viscous oil, which can suit a capsule, a dispersion or a low-dose stick. A C10-rich profile gives more body and a higher melting range, which can help a powder that needs structure or a fuller mouthfeel. Neither is better in general.

When the specification already fixes 55–65% C8 and 35–45% C10, the buyer does not need to choose a single ratio; the supplier delivers inside the window. Choose a tighter ratio only when the application or the label needs it. The product page carries the catalog specification, the grade page compares the oil loads and the identity page explains how the profile is proven. The COA page shows where the ratio sits on the certificate.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation