L-lysine HCl vs L-lysine base: dose, pH and the label
L-lysine hydrochloride and L-lysine base deliver the same lysine entity, but not the same mass, pH or label. The salt is about 80.0% lysine and 19.4% chloride; the base carries the full lysine mass and is alkaline. A formula that switches form without recalculating the dose and the label is a different product.
The same lysine dose needs about 25% more hydrochloride than base, and the label has to say which form was weighed.
Two forms, two specifications
The hydrochloride is a crystalline salt with a counter-ion; the base is the free amino acid. They have separate CAS numbers, separate molecular weights and separate certificate lines. The hydrochloride is the catalog form here, at 40 mesh. The base is a different material, not a stronger grade of the same powder.
| Line | Hydrochloride | Base |
|---|---|---|
| Label name | L-lysine hydrochloride | L-lysine |
| CAS | 657-27-2 | 56-87-1 |
| Formula and molecular weight | C6H14N2O2·HCl · 182.65 | C6H14N2O2 · 146.19 |
| Lysine per gram | About 800 mg | 1,000 mg |
| Chloride per gram | About 194 mg | None as the counter-ion |
| pH (5% solution) | 5.0–6.0 | Alkaline |
| Handling | Hygroscopic; sealed liner | More hygroscopic; less free-flowing |
The assay basis is the line that causes most confusion. The hydrochloride specification is 98.5–101.5% by titration on the dried basis, calculated as the salt. A certificate that says “lysine 99%” is describing a different basis from one that says “L-lysine hydrochloride 99%”. A figure near 80% on the lysine basis can be the same material as a figure near 100% on the salt basis.
The dose arithmetic
Convert with the molecular weights, not with the assay percentages. Lysine base is 146.19 g/mol and the hydrochloride is 182.65 g/mol, so one gram of the salt carries 146.19 ÷ 182.65 = 0.800 g of lysine. The inverse is 1.25: one gram of lysine needs 1.25 g of the hydrochloride. The chloride share is 35.45 ÷ 182.65 = 19.4%.
| What the label declares | Hydrochloride to weigh | Lysine in the dose |
|---|---|---|
| 250 mg L-lysine | 312 mg | 250 mg |
| 500 mg L-lysine | 625 mg | 500 mg |
| 1,000 mg L-lysine | 1,250 mg | 1,000 mg |
| 500 mg L-lysine hydrochloride | 500 mg | 400 mg |
Both directions matter. A brand that wants a 500 mg lysine claim needs 625 mg of the salt per serving; a brand that has a 500 mg capsule of the salt can declare about 400 mg of lysine. The salt weight is 25% above the lysine figure, and the lysine figure is 20% below the salt weight.
pH, moisture and the matrix
The salt solution is slightly acidic at pH 5.0–6.0. The base solution is alkaline, and that difference is the first physical constraint on the formula. An acidic ingredient, a buffered drink or a sealed sachet will react with the base and shift the finished pH; the salt pulls the same formula toward pH 5–6. Neither form is pH-neutral, and the finished-product pH should be measured rather than assumed from the ingredient.
Moisture is the second constraint. The hydrochloride is hygroscopic and needs a sealed liner; the base is more hygroscopic and less free-flowing. In a capsule or tablet, the salt's crystalline 40 mesh powder is easier to blend and fill. In a stick pack or a drink mix, both forms dissolve, but the chloride load and the pH change the taste and the acid balance. In a gummy or a chew, the water activity and the heat step decide how the form behaves in the process.
Which dosage form fits which
A capsule or tablet with a tight fill is the clearest case for the base: it carries 25% more lysine per milligram, so the same dose occupies less volume. The trade-off is the alkaline surface, the hygroscopy and the label name. A conventional wet granulation is usually easier with the hydrochloride, because the salt is crystalline and less alkaline, but the granulation still needs a moisture limit and a drying step.
A powder stick or a drink mix usually fits the hydrochloride: it is freely soluble, the pH is already near 5–6, and the chloride is part of the label arithmetic. A base in an acidic drink neutralises the acid and can change the flavour and the acid balance. A gummy or a chew needs a trial with the real matrix, because the water activity, the heat and the other acids decide the result more than the form alone. In every case, the form is chosen with the fill weight and the label in view, not after the formula is fixed.
What the label has to say
In the EU, the ingredient list names the form used. If the drum is L-lysine hydrochloride, the list says L-lysine hydrochloride; “L-lysine” alone does not describe the salt. The same rule applies in Great Britain under the retained food information rules, and Northern Ireland follows the EU text. A quantitative statement should say whether the figure refers to the salt or to lysine; otherwise the reader cannot reproduce the dose.
In the US, the Supplement Facts panel declares the dietary ingredient as “L-lysine (as L-lysine hydrochloride)” and the amount is the lysine figure, not the salt figure. The salt is named in the parenthetical. If the label wants to declare the salt weight, that is a separate statement and should be worded so it cannot be read as the lysine amount. There is no Daily Value for lysine, so no percentage is shown.
The claim boundary is separate from the name. In the EU and the UK, a health claim must be authorised in the register; as of this review no L-lysine claim is listed, so the label should not carry one. In the US, a structure/function statement is possible with substantiation and the DSHEA disclaimer, but it cannot be a disease claim. A compositional statement such as “L-lysine hydrochloride 500 mg” is not a health claim, but it still has to match the certificate and the basis.
When to choose which
Choose the hydrochloride when the label can name the salt, the formula can carry the chloride and the pH 5–6, and the fill weight has room for the extra 25%. It is the simpler material for a crystalline blend, a stick pack or a drink mix, and its chloride and rotation give the certificate a clear identity check. Choose the base when the dose must fit a small capsule or tablet, the formula is not acidic, and the label is written for L-lysine rather than the salt.
Choose neither without a trial when the matrix is a sealed acidic powder, a high-water gummy or a heated chew. The form changes the pH, the water uptake and the label, and those three changes belong in the trial protocol. The product hub carries the hydrochloride specification; the grades page compares the forms for grade selection; the COA page shows the certificate lines; the compliance page covers the market rules; the stability page covers moisture and shelf life.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation