02 Grade comparison

L-lysine HCl or L-lysine base: choosing a grade

Technical document 02 · Reviewed 2026-11-19 · L-Lysine Hydrochloride

On this page
  1. Why “L-lysine” is not a specification
  2. Hydrochloride and base side by side
  3. pH, hygroscopy and the chloride load
  4. What the form does to the dose
  5. What to write into the specification
  6. When the other form is the wrong answer

L-lysine is sold as the hydrochloride and as the free base, and the two are different label ingredients. The hydrochloride is about 80.0% lysine and 19.4% chloride, with a 5% solution at pH 5.0–6.0; the base carries the full lysine mass and is alkaline. The dosage form, the fill weight, the pH the matrix can carry and the name on the label decide which one fits.

In one line

The label and the dosage form choose the form; the assay percentage on the quotation does not.

Why “L-lysine” is not a specification

The base and the hydrochloride share the lysine entity but not the molecular weight, the counter-ion, the solution pH or the label name. L-lysine hydrochloride is CAS 657-27-2, C6H14N2O2·HCl, 182.65 g/mol. L-lysine base is CAS 56-87-1, C6H14N2O2, 146.19 g/mol. A certificate for one does not describe the other, and a formulation weighed for one will be wrong if the other arrives.

The second axis is physical form. The catalog grade is a crystalline powder at 40 mesh; an 80 mesh milled grade and a granulated grade are available on request. Mesh changes flow, dust and blend uniformity, not chemistry. Write both axes into the specification: the chemical form and the particle size.

Hydrochloride and base side by side

What changes between L-lysine hydrochloride and L-lysine base
LineL-lysine hydrochlorideL-lysine base
Label nameL-lysine hydrochlorideL-lysine
CAS657-27-256-87-1
Formula and molecular weightC6H14N2O2·HCl · 182.65C6H14N2O2 · 146.19
Lysine per gramAbout 0.80 g1.00 g
Chloride per gramAbout 0.194 gNone as the counter-ion
pH (5% solution)5.0–6.0Alkaline; well above the salt's window
Moisture and handlingHygroscopic crystalline powder; keep sealedMore hygroscopic and less free-flowing
Assay basis98.5–101.5% by titration, dried basis, as the saltThe base's own specification, as the base
What the label declaresThe hydrochloride, with the lysine figure calculated from itL-lysine, with no chloride load

The table is not a ranking. Each form has a job, and the job is set by the formula and by the label the brand intends to print.

pH, hygroscopy and the chloride load

The hydrochloride is the salt of a basic amino acid, and its 5% solution sits at pH 5.0–6.0. That near-acidic window is part of the specification, not an incidental reading. The free base is the alkaline form; a solution sits well above the salt's window, and an acidic component in the blend will neutralise it. If the base has taken up carbon dioxide from the air, an acidic, sealed pack can release that gas and change the pack, so the base is a poor fit for an acidic, water-containing formula with no headspace.

Both forms dissolve freely in water, so solubility seldom decides the choice. Moisture handling does. The hydrochloride is hygroscopic and must stay in a sealed liner; the base is more hygroscopic and less free-flowing, which makes weighing and blending harder. The salt also brings about 19.4% chloride by mass. That chloride is useful as an identity check on the certificate, but it is dead weight in a capsule: the same lysine dose needs more hydrochloride than base.

Particle size is the third physical variable. The 40 mesh catalog grade flows well for capsule filling and blending; an 80 mesh grade disperses faster but can dust more; a granulated grade reduces dust and improves flow with a different dissolution profile. None of these changes the form or the label.

What the form does to the dose

The conversion is arithmetic. One gram of the hydrochloride delivers about 800 mg of lysine; to declare 1,000 mg of lysine from the salt, a formulator needs about 1,250 mg. A 500 mg capsule of the salt carries about 400 mg of lysine, so a label that says “L-lysine hydrochloride 500 mg” is not declaring 500 mg of lysine.

Lysine declared and hydrochloride weighed
DeclarationHydrochloride neededLysine delivered
250 mg lysineAbout 312 mg250 mg
500 mg lysineAbout 625 mg500 mg
1,000 mg lysineAbout 1,250 mg1,000 mg
500 mg hydrochloride500 mgAbout 400 mg

The difference lands on the fill weight. A capsule with a tight fill may not have room for the extra 25% of salt, while a stick pack or a drink mix usually does. In a tablet, the alkaline base can affect the granulation pH and the choice of excipients; the salt is easier to run in a conventional wet granulation, but it still needs a moisture-controlled process. In a gummy or a chew, the water activity and the heat step matter more than the form alone. The dose decision should be written before the purchase order, not after the first trial.

What to write into the specification

  • “L-lysine hydrochloride, CAS 657-27-2, C6H14N2O2·HCl; not L-lysine base.”
  • “Assay 98.5–101.5% by titration on the dried basis, calculated as the hydrochloride.”
  • “Specific rotation +20.4° to +21.4° on the dried basis; chloride 19.0–19.6%; pH (5% solution) 5.0–6.0.”
  • “Loss on drying ≤0.5%; residue on ignition ≤0.1%; heavy metals and microbiology as on the catalog specification.”
  • “Particle size 40 mesh, or the agreed 80 mesh or granulated distribution.”
  • “Label declaration to name the hydrochloride and to state whether the quantity is the salt or the lysine.”

The specification is form-specific. A range copied from the base and applied to the salt is not a specification; it is a template with the wrong noun. The assay basis, the chloride line, the rotation and the pH range all change with the form.

When the other form is the wrong answer

Do not choose the base for an acidic, sealed powder if the formula has no room for the carbon dioxide the base can carry. Do not choose the hydrochloride when the label has to read “L-lysine” and the dose is expressed as lysine, unless the artwork is changed to match the salt. Do not switch forms to fix a flow problem: mesh and granulation are the tools for flow, and changing the salt to solve a hopper creates a labelling problem instead.

The catalog form is the hydrochloride at 40 mesh. The product hub carries the specification; the COA page shows how each line is reported; the hydrochloride-versus-base page works through the dose and label arithmetic; the stability page covers moisture and packaging; the compliance page covers the label rules.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation