06 Identity & adulteration

How we prove a vitamin K2 MK-4 oil lot is menaquinone-4

Technical document 06 · Reviewed 2026-11-20 · Vitamin K2 MK-4 Oil

On this page
  1. What has to agree
  2. The ratio: menaquinone to carrier, and trans to cis
  3. X-ray diffraction: a limited role for an oil
  4. Signals of a substitution
  5. Identity lines for the specification
  6. What to ask before you buy

An MK-4 1% oil lot is menaquinone-4 in a declared carrier when four figures agree: HPLC retention and UV spectrum match a menaquinone-4 reference, the concentration sits inside 1.0–1.1%, the peroxide value shows an oil still inside its limit, and the fatty-acid profile matches the declared carrier. The document names the substance and the carrier, but it does not prove the oil on its own. The assay alone cannot show whether the oil is fresh or whether the carrier is the declared one.

In one line

An MK-4 oil is proved by four agreeing figures: the chromatogram and its UV spectrum, the concentration against a standard, the peroxide value, and the fatty-acid profile of that carrier.

What has to agree

A sheet can carry the right name and still not prove the oil. Each item below is a separate question, and an answer to the first alone describes paperwork.

Five checks for a 1% MK-4 oil
CheckQuestionMethodWhat it shows
DocumentAre the substance and the carrier named?Name, CAS number, carrierPaperwork only
ChromatographyIs the menaquinone MK-4?HPLC retention and UV spectrumThe molecule, not the strength
ConcentrationIs the blend strength as declared?HPLC against a standard; mass balanceThe declared percentage
CarrierIs the oil the declared oil?Fatty-acid profile by GCThe carrier identity
FreshnessIs the oil in good condition?Peroxide value, p-anisidine value, free fatty acidCondition, not identity

The ratio: menaquinone to carrier, and trans to cis

The blend is a ratio before it is anything else: about one part menaquinone-4 to 99 parts carrier. At 1.0–1.1% that is 10–11 mg of MK-4 per gram, and a result of 0.8% is not “close enough” for a 1% claim, because every serving would be a fifth short. A result above the range is also a problem, since it changes the dose arithmetic and the label.

The second ratio sits inside the molecule. The menaquinone side chain carries a double bond that can be trans or cis, and the all-trans configuration is the one the reference standard describes. Light and heat can isomerise part of a lot, and a total assay can stay inside 1.0–1.1% while the all-trans share falls. If the form matters to the buyer, the all-trans share is agreed as a line and reported with its method.

The mass balance is the third ratio. The assay, the carrier and the minor components should add to 100%; a lot with 1.05% MK-4 and a high peroxide value still has the right concentration, but the carrier has changed. That is why the concentration and the oxidation panel are read together rather than as one number.

X-ray diffraction: a limited role for an oil

X-ray diffraction reads a crystal lattice. In a 1% oil, menaquinone-4 is dissolved and the carrier is liquid at room temperature, so there is no MK-4 lattice to diffract and no pattern that identifies the molecule. A certificate line that says “XRD conforms” on an oil has proved very little, and a buyer should not accept it in place of a chromatogram.

XRD has a use when the question is solid form. It can compare a crystalline MK-4 reference with an isolated powder, show whether a carrier is partly crystalline, or detect a crystalline foreign solid in an oil. Even then, ask for the reference diffractogram and the limit of detection before accepting a “match”. For this product the routine identity tests are HPLC with UV and the carrier profile, not diffraction.

Signals of a substitution

Substitutions in a 1% MK-4 oil and how they show
SubstituteEffectSignMethod
Extra carrierLowers the concentration and shortens the doseAssay below 1.0%; mass balance offHPLC against a standard
Another menaquinoneSimilar colour, different homologueRetention time or spectrum differsHPLC/UV, LC-MS
Substitute carrier oilChanges the declared ingredientFatty-acid profile and cloud point differGC fatty-acid profile
Oxidised oilBlends old oil with freshPeroxide, anisidine and free fatty acid highOxidation panel
DyeImitates the yellow colourColour but no UV matchUV spectrum, HPLC

Appearance is the least reliable sign: the yellow-to-amber window is broad and a dye can imitate it. Trust the chromatogram, the concentration against the standard, the carrier's fatty-acid profile and the oxidation panel instead. A sheet with appearance and assay but no identity work has skipped the substitution most likely to occur.

Identity lines for the specification

  • “Menaquinone-4 (MK-4), CAS 863-61-6, C31H40O2, 1.0–1.1% w/w in a declared food-grade oil.”
  • “Identification by HPLC retention time and UV spectrum against a menaquinone-4 reference.”
  • “Assay by HPLC with UV detection, reported on the oil as sold.”
  • “Carrier identity by fatty-acid profile, with the source, allergen and GMO statements.”
  • “Peroxide value ≤10.0 meq O₂/kg; p-anisidine value and free fatty acid can be agreed.”
  • “All-trans share of the menaquinone, if agreed, with the method and limit.”

What to ask before you buy

  1. Which carrier oil does this lot use, and what is its fatty-acid profile?
  2. Will you send the chromatogram and the UV spectrum, not just the assay figure?
  3. What are the peroxide, p-anisidine and free fatty acid results, with their test dates?
  4. What is the all-trans share of the menaquinone, and how was it measured?
  5. If a result is disputed, would you join a re-test on the retained sample?

Straight answers to those five questions add up to an identity file. Catalog limits are on the product hub; the COA page maps each figure to a certificate line; the grade page compares the oil with the isolated powder; the HPLC method note explains the separation; the quality page covers the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation