What the COA for vitamin K1 1% powder actually reports
The certificate for a vitamin K1 1% powder lot reports appearance, HPLC and UV identification, assay by HPLC, loss on drying, heavy metals, microbiology and particle size. The assay is a concentration on a carrier, not a purity: 1.0–1.1% phytonadione means roughly 99% of the powder is carrier and moisture. The limits below are the catalog specification; the batch COA releases a particular pack.
A 1% assay is a concentration, not a purity, so the certificate has to name the carrier, state the assay basis and show the HPLC identity that proves the vitamin is phytonadione.
The certificate as a test report
A row earns its place when a reader can check it: it names the measurement, the method and the limit the lot was released against. On a carrier powder the identity and assay rows carry more weight, because the appearance of a pale yellow powder says very little about the vitamin dispersed through it.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Light yellow to yellow powder |
| Identification | HPLC retention and UV spectrum against a phytonadione reference | Conforms to the reference |
| Assay | HPLC with UV detection | 1.0–1.1% phytonadione |
| Loss on drying | Gravimetric on the blend | ≤5.0% |
| Heavy metals | ICP-MS, per element | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Absence tests and plate count | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; absent: E. coli, Salmonella |
| Particle size | Sieve analysis, 80-mesh screen | ≥95% through 80 mesh |
The sheet should also name the carrier and any antioxidant, with its level. Those lines are not in the catalog table, but they describe the other 99%; a certificate that omits them has identified the vitamin and left the carrier unknown.
What 1.0–1.1% is a percentage of
One kilogram of powder at 1.0% carries 10 g of phytonadione; at 1.1% it carries 11 g. That is why the figure is a content, not a purity test. The certificate should say whether the result is on the powder as received or on the dried basis. The catalog limit carries no basis note, so the basis has to be read from the certificate and agreed before release.
The loss on drying line supplies the conversion. A lot that measures 1.00% as received at 4.0% moisture calculates to 1.04% dried; at 5.0% the same powder calculates to 1.05%. The window holds both, but a certificate that mixes the bases across lots is not describing a stable product. Ask for the basis in the assay row, not a footnote.
The 0.1-point window is about 10% of the target, roughly ±5% around the midpoint; blending, sampling and moisture move inside it. A lot at 1.02% and one at 1.09% both pass yet differ by 7% in vitamin content per gram.
The powder specification has no related-substances line. That is not an oversight to ignore: on a powder that is 99% carrier, a peak-area normalisation has little meaning. The cis isomer and menadione are better controlled on the oil before blending, or measured by a validated method against a phytonadione standard with a carrier blank. Ask which route the supplier uses.
Release limit versus batch result
A release limit defines what will be accepted; a batch result records what was found. The two belong in separate columns, with the method beside them, because a result column filled with the specification range says nothing about the lot.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 1.0–1.1% by HPLC | A measured percentage with its basis and method |
| Loss on drying | ≤5.0% | A measured percentage |
| Carrier | Identity agreed on the specification | The carrier name and its own specification |
| Heavy metals | Per element | A figure in mg/kg for each element |
| Microbiology | Counts and absence | The count plus the absence result for the lot |
| Particle size | ≥95% through 80 mesh | The percentage that passed the sieve |
“Conforms” is a conclusion, not evidence. For identification the evidence is a retention time and a UV spectrum against a phytonadione reference; for the carrier it is the carrier name and the supplier's own specification or certificate. A certificate that reports the assay to two decimals and leaves the carrier as a footnote has optimised the smaller line. The same test applies to the sieve result: 80 mesh is a specification, and the measured percentage through the sieve is the result.
What moves between batches
Four things move between lots. The carrier lot changes colour slightly and can change bulk density and flow. Blending decides content uniformity: a drum sampled top and bottom should give the same assay, and a spread is a mixing signal rather than an HPLC error. Drying and milling move loss on drying and particle size. Light exposure before sealing moves the colour and, at the margin, the isomer figure.
Colour is the weakest line. Light yellow to yellow is a broad window, and a shift within it is not a rejection. A powder that looks darker or duller than the previous lot may reflect a longer hold, a warmer drying step or a different carrier while the assay still passes. Ask for the batch record and the carrier lot before rejecting on appearance alone.
Content uniformity deserves its own sample: a 1% powder can pass a 1 g assay while a 10 mg scoop is not representative.
When to order an outside test
An outside laboratory earns its fee when a source is new, when a shipment enters a regulated market for the first time, when potency is disputed or when the certificate does not establish the carrier. The panel is HPLC with a diode-array detector and a phytonadione standard, assay with its basis, loss on drying, ICP-MS metals, microbiology and a sieve analysis.
Add carrier identity by FTIR against a reference, the antioxidant identity and level if one is declared, and cis isomer or menadione if the chromatogram shows peaks the certificate does not explain. For a drum, sample more than one position and report each result; a single composite hides the segregation that matters at the weighing station.
Every screen needs its detection limit beside the result; a “not detected” line with no figure describes the method. Tested and retained samples should be the same, and the report should carry the lot code from the pack.
What to compare between suppliers
Seven lines repay a side-by-side read: form and CAS number; declared content and basis; carrier identity and statements; particle size; loss on drying; metals and microbiology; pack size and lot code. Two offers that agree on 1% but differ on carrier or basis are not the same powder.
The second layer is traceability: who blended the lot, which carrier lot was used and whether an antioxidant was added.
The catalog numbers are on the vitamin K1 1% powder product page. The grade levers are compared on the grades page; the mass arithmetic is on the oil versus powder page; the parent oil is on the vitamin K1 page; the separation behind the assay is described in the analytical methods library; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation