02 Grade comparison

Vitamin K1 powder grades: potency, carrier and particle form

Technical document 02 · Reviewed 2026-11-20 · Vitamin K1 1% Powder

On this page
  1. Why a carrier grade exists
  2. The milled powder, the granulated finish and the oil
  3. Particle size, flow and dispersion
  4. Dose arithmetic and the blend
  5. What to write into the specification
  6. When the 1% powder is the wrong grade

The catalog vitamin K1 powder is a 1% grade: phytonadione on a carrier at 1.0–1.1% by HPLC, milled to 80 mesh. Potency, carrier and particle form are three separate decisions; the catalog fixes potency at 1%, while the carrier and particle form are named on the lot. A granulated finish or the neat oil changes the mass per dose, the flow and the label, so the grade should follow the dosage form.

In one line

A powder grade is defined by three things — the declared potency, the carrier and the particle form; the 1% catalog grade fixes the potency, and the other two belong on the specification.

Why a carrier grade exists

Phytonadione is a viscous oil at room temperature. The dose is measured in micrograms, and a 100 µg dose is about 0.1 mg of the oil, a quantity no capsule line can weigh. A carrier grade solves two problems at once: it turns the oil into a solid that can be blended and filled, and it dilutes the vitamin to a concentration that ordinary weighing equipment can handle. At 1%, a 100 µg dose is 10 mg of powder — still small, but within reach of a laboratory balance and a premix step.

That is why the 1% grade works as a premix, not a stand-alone fill. In a 500 mg capsule blend it is 10 mg, about 2% of the fill; the rest is other actives and excipients. The carrier is what lets the vitamin be distributed evenly and weighed without a microbalance.

The oil remains the parent material. A buyer who needs an oil fill, an oil blend or an emulsion buys the oil; a buyer who needs a solid buys the carrier grade. Neither is a substitute for the other, and the certificate for each describes a different product.

The milled powder, the granulated finish and the oil

Powder grade, granulated finish and the neat oil · vitamin K1
Property1% powder, 80 mesh (catalog)1% granulated (on request)Neat oil (sibling product)
FormLight yellow, free-flowing powderCoarser granule from the same blendClear yellow to amber viscous oil
Declared content1.0–1.1% phytonadione by HPLC1.0–1.1%, same blend, different finish97.0–103.0% phytonadione by HPLC
Mass for a 100 µg doseAbout 10 mgAbout 10 mgAbout 0.1 mg
Typical useCapsule and tablet blends, stick packsBlends that need flow and low dustSoftgels, oil blends, emulsions
LabelVitamin K (as phytonadione) plus carrierSame, with the granulated carrier profileVitamin K (as phytonadione); carrier oil if blended

The table makes the point that potency and particle form are different levers. The granulated finish is the same 1% blend with a coarser particle; it changes flow, dust and segregation, not the vitamin content. The oil is a different product with a different specification and a different certificate.

A different declared content would be a new specification, not a variant of this page; the carrier, the uniformity and the label would have to be rebuilt around it.

Particle size, flow and dispersion

The catalog powder is ≥95% through 80 mesh. That figure is a finishing specification: it says the mill and the sieve were set to give a fine, free-flowing powder, not that the vitamin is evenly distributed at every scale. A finer powder disperses faster and dusts more; a coarser granule flows better and traps less air.

Bulk density and flow are not on the catalog table, yet they decide whether a blend runs. Ask for both if the powder feeds a dosator or a sachet line. Granulation answers dust or segregation and does not change the declared content.

Water dispersibility is a property of the powder, not of the vitamin. The catalog describes the powder as dispersible in water as supplied, while phytonadione itself is fat-soluble. A dispersion is not a solution: the vitamin stays in fine droplets or on carrier particles, and a clear drink needs an emulsion rather than a stir.

Dose arithmetic and the blend

The arithmetic is a division by the declared content. At 1.0%, a 75 µg dose is 7.5 mg of powder, a 100 µg dose is 10 mg and a 1 mg dose is 100 mg. At 1.1% the same doses are 6.8 mg, 9.1 mg and 90.9 mg. Those differences are small against a 500 mg capsule, but they matter when the powder is a minor premix and the blend is built to a tight label claim.

In a 500 mg capsule, 10 mg of the 1% powder delivers 100 µg and occupies 2% of the fill. At a 1 mg claim the same capsule would need 100 mg, or 20% of the fill, and the carrier starts to compete with the other ingredients for space. That is the point at which a more concentrated grade or an oil fill becomes the better dosage-form decision.

Weigh the powder, not the vitamin, and calculate from the declared content printed on the certificate. A formula built on 1.0% that receives a 1.08% lot will over-deliver by about 8%; built on 1.08% and filled with a 1.00% lot, it under-delivers by about 7%. The error sits in the premix, not in the capsule fill.

What to write into the specification

  • “Vitamin K1 (phytonadione, phylloquinone), CAS 84-80-0, C31H46O2, on a carrier.”
  • “Declared content 1.0–1.1% by HPLC; state whether the result is as received or dried.”
  • “Carrier identity and its specification; antioxidant identity and level if one is used.”
  • “Loss on drying ≤5.0%; particle size ≥95% through 80 mesh, or the granulated profile.”
  • “Identification by HPLC retention and UV spectrum against a phytonadione reference.”
  • “Heavy metals and microbiology as listed; pack 1 kg foil pouch or 25 kg fiber drum.”
  • “Label name: vitamin K (as phytonadione), with the carrier in the ingredient list.”

We supply the 1% milled powder; a granulated finish is a separate packing option, and the oil is a separate product.

When the 1% powder is the wrong grade

The 1% powder is a poor fit when the dose is small and the capsule is single-ingredient. A 100 µg dose needs 10 mg of powder, which is below a practical capsule fill; the oil or a more concentrated grade suits that format better.

It is also the wrong choice for a clear beverage, because the vitamin is not water-soluble and the powder gives a dispersion, not a solution. An emulsion is a development project, not a scoop of powder.

Where the plant has oil handling, an oil fill carries no carrier and no carrier line on the label. Where the plant has only powder handling, the carrier grade is the practical route, and granulation is the lever for flow.

The catalog specification sits on the vitamin K1 1% powder product page. The oil is described on the vitamin K1 product page; the carrier arithmetic is set out on the oil versus powder page; the assay method is described in the analytical methods library; the release file is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation