01 COA & batch testing

What the COA for vitamin E 50% powder actually contains

Technical document 01 · Reviewed 2026-11-18 · Vitamin E

On this page
  1. The certificate as a test report
  2. What the 50% measures
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a vitamin E 50% powder reports appearance, identification by HPLC retention time, tocopheryl acetate at 50.0–55.0% by HPLC, the IU equivalent calculated from it, loss on drying, the declared carrier, dispersibility, particle size, the heavy-metal panel and microbiology. The ranges on this page are the catalog specification for the water-dispersible powder; the batch COA is the document that confirms a particular pouch or drum. The 50% is a mass fraction of the acetate, not of vitamin E in general, and the IU figure follows from it.

In one line

The certificate's 50% is tocopheryl acetate by HPLC, not vitamin E in general; the IU figure and the carrier follow from that number.

The certificate as a test report

A certificate is auditable when each row names the parameter, the method and the limit the lot was released against. For a 50% powder the sheet needs one line that a pure vitamin does not: the carrier, because about half of the powder is not the vitamin.

Identity, assay and matrix · vitamin E 50% water-dispersible powder
ParameterMethodRelease limit
AppearanceVisualWhite to off-white, free-flowing powder
IdentificationHPLC retention timeConforms to the tocopheryl acetate reference standard
Tocopheryl acetateHPLC, UV detection50.0–55.0%
Potency equivalentCalculated at 1 mg = 1 IU500–550 IU/g
Loss on dryingGravimetric≤5.0%
CarrierDeclarationModified starch and silicon dioxide, declared
DispersibilityWater dispersion testDispersible in cool water, forming a milky emulsion
Particle sizeSieve analysis100% through 40 mesh

Identification is a conformance statement rather than a measured value, and carrier is a declaration; on request the certificate can state the proportion. The rest are measured lines, and each should carry a unit and an acceptance limit.

What the 50% measures

The assay reports tocopheryl acetate, the acetate ester of alpha-tocopherol. Its molecular mass is 472.74 g/mol, and the labelling convention assigns 1 IU to 1 mg of the dl form, so 50.0–55.0% is 500–550 mg/g and 500–550 IU/g. At the bottom of the window one IU is 2.0 mg of powder; at the top it is 1.82 mg. That is the arithmetic a formulator uses to turn a label dose into a fill weight, and it only works when the certificate names the form.

The acetate result is not a tocopherol result. Releasing the acetyl group changes the mass: the same lot expressed as free tocopherol would read about 91% of the acetate figure on a mass basis, and a supplier who reports “vitamin E 50%” without the form leaves the reader to guess which number is on the sheet. This catalogue's grade is the dl-acetate, and the certificate should say so next to the assay.

The basis has to be stated as well. Loss on drying is allowed up to 5.0%, so a result reported on the dried basis is higher than the same powder as sold; 50.0% on dried material is about 47.5% at the top of the moisture limit. The carrier is the remainder — modified starch and silicon dioxide, declared — not a diluent to be inferred from a difference.

Release limit versus batch result

The release limit is the acceptance boundary; the batch result is what the laboratory measured on that lot. Both belong on the sheet, in separate columns, with the method beside them. A result column filled with the specification range is a copy of the gate, not a result. Dispersibility is a pass or fail observation — a milky emulsion in cool water — and particle size is a sieve result, 100% through 40 mesh; neither has a window to negotiate.

The IU line is calculated from the assay, not measured a second time. If the certificate prints a percentage and an IU/g figure that do not reconcile at 1 IU per milligram, one of them is on a different basis or describes a different form.

“Passes specification” is a conclusion the reader should be able to reach from the numbers. Ask for the chromatogram when the assay sits near 50.0% and for the sieve record when the powder is destined for a capsule fill. The lot code, the manufacturing and expiry dates and the pack size belong on the same sheet as the results.

What moves between batches

The assay moves with the ratio of acetate to carrier in the drying feed and with the losses in the dryer. The 50.0–55.0% window is wide enough to matter: a formulator who doses by weight needs about 10% more powder per IU at the low end than at the high end. The carrier lot changes the powder's flow and moisture pick-up even when the assay is unchanged.

Loss on drying moves with the carrier and with the drying step, and particle size moves with the mill and the sieve. Colour is less quantitative and often more revealing: a yellow or tan tint can point to heat exposure or oxidation while the assay still passes. A rise in free tocopherol on the chromatogram is the same story told analytically. A trend across lots says more than one result near an edge.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a label claim that has to be defended, or a disputed result. The useful panel is an HPLC run against a tocopheryl acetate standard with a co-injection, a saponification or infrared check that the ester is present, a recalculation of the IU figure, ICP-MS for the metals and the microbiological suite.

Ask the laboratory to state its detection limit and to attach the chromatogram. A “not detected” line without a limit is evidence about the method's sensitivity, not about the sample. Chain of custody matters: the sample tested should be the sample retained, and the lot code on the certificate, the pack and the sample should match.

What to compare between suppliers

Put seven lines side by side: the form and isomer; the assay result and method; the IU/g equivalent; loss on drying and its basis; the carrier and its proportion; dispersibility and particle size; and the contaminant and microbiological panels. Two quotations that match on 50% but differ on the form, the carrier or the basis are not describing the same powder.

The second layer is traceability. The certificate should name who manufactured the lot, the specification version it was released against, and the pack the lot went into. A correct certificate can still belong to a pouch other than the one on the loading dock.

The catalog specification sits on the vitamin E product page. The forms are compared on the grade page; the tests that separate the acetate from other esters are on the identity page; the ordering unit is on the MOQ page. The chromatographic method is described in the HPLC method note, and the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation