03 Stability

Vitamin E is sensitive to oxygen and light; the carrier decides the rest

Technical document 03 · Reviewed 2026-11-18 · Vitamin E

On this page
  1. The powder in the unopened pack
  2. In water and in oil
  3. The five factors that decide the loss
  4. How the stability is tested
  5. What the formula does to the powder
  6. Assigning and reading the shelf life

The acetate ester is more resistant to oxidation than the free tocopherol, but a 50% powder is still a fat-soluble vitamin spread on a starch carrier, and oxygen, light, heat, trace metals and moisture all take it down over time. The pack decides how much of that the lot meets before it is opened; the formula decides what happens after. This page sets out what fails, how it is tested and what to write into the specification.

In one line

The acetate ester resists oxidation better than the free vitamin, but light, heat, trace metals and a wet carrier still decide how long the powder keeps.

The powder in the unopened pack

Dry, the powder is reasonably stable. The acetate group blocks the phenolic hydroxyl that makes the free tocopherol reactive, so the main reactions are slow: hydrolysis of the ester, held back by the low moisture of the carrier, and oxidation of the chromanol ring, held back by the ester and the pack. The specification's loss on drying of ≤5.0% is the control that keeps that water activity low.

The carrier is the weak point in storage, not the vitamin. Modified starch picks up moisture from the air, and a powder above the moisture limit cakes, loses flow and gives up its dispersion. Silicon dioxide helps flow but does not stop moisture ingress. A sealed foil pouch with a small headspace is the practical barrier; a fibre drum with a liner is the bulk equivalent. Store cool, dry and dark, keep the pack closed between weighings, and use stock in rotation.

Two analytical signs track storage. Free tocopherol rises as the acetate hydrolyses, and colour drifts yellow or tan as oxidation products form. Both can appear while the assay is still inside 50.0–55.0%, which is why the assay alone is a weak stability measure.

In water and in oil

The powder does not dissolve; it disperses. In cool water it forms a milky emulsion of oil droplets stabilised by the carrier, and those droplets have a large surface area exposed to dissolved oxygen. A beverage therefore stresses the vitamin more than the same mass in a sealed pouch, especially when the drink is pasteurised, stored warm or exposed to light.

pH matters. Hydrolysis of the acetate is faster at alkaline pH, so a matrix that drifts alkaline shortens the effective life of the ester even when the powder was released correctly. Acidic matrices are slower but not inert, and a high-water-activity gel or syrup gives the reaction more freedom than a dry blend. Trace metals are the other accelerant: iron and copper at low levels catalyse oxidation, and a mineral premix can supply both.

In oil, the vitamin is in its natural habitat, but the carrier oil becomes part of the stability problem. A polyunsaturated oil oxidises and takes the vitamin with it, so the peroxide value of the oil phase belongs in the review. In a gummy, the cook temperature, the water activity and the pH all act at once, and the powder's dispersion has to survive a process that a pouch never sees.

The five factors that decide the loss

What degrades vitamin E in a powder and how to limit it
FactorEffectControl
OxygenOxidation of the chromanol ring; colour driftSealed foil pouch, low headspace, closed pack between weighings
LightPhotodegradation at the surface of the powderOpaque pack; dark storage; covered hopper
HeatFaster oxidation and hydrolysis; losses in cookingCool storage; short thermal exposure; check the process step
Trace metalsIron and copper catalyse oxidationMetal-free contact; review the mineral premix
Moisture and pHHydrolysis of the ester; caking; loss of dispersionLoss on drying ≤5.0%; dry storage; pH of the matrix

The five act together, and the weakest one sets the shelf life. A dark, cool, sealed pack removes most of the risk in storage; a warm, clear bottle of an alkaline drink removes almost none of it. A stability programme that tests only the powder in its pouch answers the warehouse question, not the product question.

How the stability is tested

Test the material in the pack it will be sold in, and test the finished matrix separately. The standard design uses three lots, time points at 0, 1, 3, 6, 12, 24 and 36 months, and two conditions: 25 °C at 60% relative humidity for the real-time series, and 40 °C at 75% relative humidity for the accelerated series. The accelerated series supports the assignment; the real-time series assigns it.

The panel should follow the certificate where it can: tocopheryl acetate by HPLC, loss on drying, appearance, dispersibility and the impurity or free-tocopherol profile. Add the finished-product tests that matter to the dosage form — potency uniformity, colour and, for a beverage, the dispersion at the end of shelf life.

What the formula does to the powder

A matrix is not a neutral carrier for a vitamin. An acidic stick pack, a gummy cooked at high temperature, a tablet with a mineral premix and a beverage with dissolved oxygen each set their own loss rate. The formulator's question is not whether the powder is stable in the abstract but whether the label claim is still met at the end of the finished product's shelf life.

That is where overage is decided. An overage is a calculated addition, based on the measured loss in that matrix, that keeps the label claim true at expiry. It is not a substitute for a stable matrix, and it does not repair a process that destroys the vitamin. Write the target, the overage basis and the test method into the formula record, and test the worst-case pack rather than the most convenient one.

Assigning and reading the shelf life

The shelf life is a property of the material, the pack and the storage condition together. A sealed 1 kg foil pouch of this grade is commonly assigned 24 months; the figure that applies to your lot is the one the supplier's stability data supports for the pack you buy, so confirm it on the technical data sheet rather than assuming it. The certificate carries the manufacturing and expiry dates, and the remaining shelf life on arrival is a legitimate order term.

Once the pack is opened, the sealed-pack figure no longer describes the material. Weigh out what the batch needs, close the pouch, keep it dry and dark, and use the remainder within the period your own risk assessment supports. Re-testing an opened pack can confirm that a lot is still inside specification, but it does not extend the assigned shelf life without a protocol that says so.

The catalog ranges are on the vitamin E product page. The assay and moisture lines are explained on the COA page; the forms are compared on the grade page; the pack sizes are on the MOQ page. The moisture test is described in the loss-on-drying note, and the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation