What the COA for vitamin D2 actually contains
The certificate for a vitamin D2 lot reports appearance, identification by HPLC and ultraviolet spectrum, assay by HPLC, melting range, loss on drying, the heavy-metal panel, microbiology and particle size. The assay only means ergocalciferol when the reference standard and the identity tests point to the same molecule. The limits below describe the catalog grade; only the batch certificate speaks for a particular pack.
A vitamin D2 assay is only an ergocalciferol result when the reference standard, the ultraviolet identity and the melting range agree with it.
The certificate as a test report
A certificate earns its keep when a reader can audit it line by line. Each parameter needs its measured value, the method that produced it and the limit it was judged against. A row that says only “conforms” gives a verdict without the raw observation.
The identity of vitamin D2 rests on more than one line. HPLC retention against an ergocalciferol standard names the peak; the ultraviolet spectrum shows the vitamin D chromophore; the melting range shows a crystalline sterol with the expected solid form. Any one of the three can be right while another is wrong.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White crystalline powder |
| Identification | HPLC retention and UV spectrum; melting range | Conforms; 115–118 °C |
| Assay | HPLC with UV detection | 97.0–103.0% |
| Loss on drying | Gravimetric | ≤0.5% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
The assay basis, the standard and the IU arithmetic
The assay is a percentage of the powder, and the certificate should state whether that percentage is on the as-is or the dried basis. The specification here allows loss on drying up to 0.5%, so the gap between the two figures is small but not zero: a lot at 97.0% as-is with 0.4% moisture calculates to 97.39% on the dried basis. Both numbers can be correct; they describe different denominators.
The reference standard matters more than the basis. Ergocalciferol and cholecalciferol have similar ultraviolet spectra, with a maximum near 265 nm, and a method that reports “vitamin D” without naming the standard has not shown which molecule it measured. The certificate should name an ergocalciferol standard and state whether a cholecalciferol screen was run.
The IU figure is a conversion, not a second assay. One microgram of either vitamin D form is assigned 40 IU, so 1 mg is 40,000 IU. A 99.0% powder therefore carries 990 mg of ergocalciferol per gram, or 39,600,000 IU/g. That arithmetic is a unit check on the certificate, not a dose, and it explains why this bulk material is diluted before it reaches a capsule.
The melting range is a second identity line. The catalog range is 115–118 °C for ergocalciferol. A result outside that window can point to a different sterol, a solvate or an impurity that the assay does not see.
Release limit versus batch result
The release limit marks the boundary a lot must stay inside. The result belongs to the batch in hand. The certificate needs both, in separate columns, with the method named alongside. A result column that repeats the limits has copied the gate instead of recording a measurement.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | 97.0–103.0% on the stated basis | A measured percentage, with the basis and the reference standard |
| Identification | HPLC/UV conform; 115–118 °C | The retention time, the spectrum and the measured melting range |
| Loss on drying | ≤0.5% | A measured percentage |
| Heavy metals | Per element | A measured figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
“Passes specification” is a conclusion. For heavy metals the evidence is a figure per element, not a single total; for microbiology it is a count plus an absence statement; for assay it is a measured percentage with the basis and the standard. A certificate that reports one “vitamin D” figure and no chromatogram has left the form untested.
What moves between batches
Vitamin D2 is made by ultraviolet irradiation of ergosterol, and the reaction produces a family of isomers. Previtamin D2, lumisterol and tachysterol are the usual companions, and the purification step decides how much survives. A batch can sit inside the assay range while its isomer profile moves. That is why the chromatogram deserves a look even when the percentage passes.
Crystallisation and drying move the melting range, the colour and the loss on drying. Milling shifts the particle-size result while the chemistry stays the same. The 40 mesh line belongs to finishing, so a new mill or sieve can move it without any change in the molecule.
A drift across several lots tells you more than one value sitting near a limit: assay drifting low, a new peak in the chromatogram, or a melting range that no longer sits in the middle of the window. Check that the lot code on the certificate also appears on the pouch, the drum and the retained sample.
When to order an outside test
An independent test is worth ordering for a new source, an opening shipment into a regulated market, a contested identity, or a label that names ergocalciferol while the certificate stays vague. The useful panel is HPLC with a diode-array detector against an ergocalciferol standard, the ultraviolet spectrum, the melting range, loss on drying, ICP-MS for the heavy metals and microbiology. Add a cholecalciferol screen by retention or by mass detection when the form is in question, and residual solvents if the supplier's route uses them.
The laboratory should state the detection limit it reached for the D3 screen. A “not detected” entry with no limit describes the method's reach, not the sample. Keep the chain of custody intact: test the sample that was retained, and make sure the report names the lot.
What to compare between suppliers
Compare six lines: form and CAS number; assay result, basis and reference standard; identity by HPLC/UV and melting range; isomer profile; loss on drying and particle size; contaminants, pack size and lot code. If two offers agree on the assay but not on the standard or the basis, they are not describing the same powder.
Traceability is the next layer. The certificate should name the manufacturing site, the specification version and the pack. The grade and its limits are listed on the vitamin D2 product page. The tests that separate D2 from D3 are on the identity page; the label consequences are on the D2 versus D3 page; the HPLC method is described in the HPLC method note, with the wider set in the analytical methods library; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation