06 Identity & adulteration

How we prove a pyridoxine lot is the hydrochloride

Technical document 06 · Reviewed 2026-11-18 · Vitamin B6

On this page
  1. Four layers, each answering a different question
  2. Reading the infrared identification
  3. The titration and the chromatogram
  4. The 1:1 salt ratio
  5. The chloride and pH figures prove the salt
  6. Where XRD fits, and where it does not
  7. Three ways a B6 powder can be wrong
  8. Writing identity into the specification
  9. Five questions for the supplier

Identity for a pyridoxine hydrochloride lot rests on four layers: the document tying the pack to a lot, the infrared spectrum matching the molecule, the titration measuring the salt, and the chloride and pH figures proving the counter-ion. The catalog requires IR to conform, assay 99.0–101.0% on the dried basis and chloride 16.9–17.6%.

In one line

The IR spectrum names the molecule, the titration measures it, and the chloride and pH figures prove the salt; any one of them alone leaves a gap.

Four layers, each answering a different question

What each identity layer proves for pyridoxine hydrochloride, and what it cannot
LayerEvidenceWhat it provesWhat it misses
DocumentName, CAS 58-56-0, lot code, certificate, retained sampleThe paper describes this packNothing about the powder
SpectroscopicIR against a reference standardThe functional groups are those of pyridoxine hydrochlorideQuantity and chloride stoichiometry
Titration and chlorideAssay on the dried basis; argentometric chlorideHow much salt is present and that the counter-ion is chlorideOther B vitamins and non-absorbing diluents
ChromatographicHPLC retention time and peak purity; LC-MS on requestWhat else is present and whether the main peak is pureNot a stand-alone release identity

The layers are cumulative. An assay alone is one layer; a certificate with the spectrum, the chloride figure and the chromatogram gives four and lets the lot be audited.

Reading the infrared identification

Pyridoxine hydrochloride shows the pyridine ring, the phenolic hydroxyl and the hydroxymethyl groups, and the hydrochloride adds an N–H absorption the free base lacks. The test compares the sample with a reference spectrum run under the same conditions. A potassium bromide disc and an attenuated-reflectance accessory give different spectra, so a certificate comparing one against the other compares two techniques.

P5P does not give the same spectrum: the aldehyde carbonyl and phosphate P–O bands are new, and the O–H region changes with the hydrate. IR is the first screen against a form switch, and extra bands the reference lacks are the useful signal. A library match score is a similarity measure, not proof of purity.

The titration and the chromatogram

The quantitative layer is a non-aqueous titration: the sample is taken up in formic acid with acetic anhydride, perchloric acid is added to the endpoint, and the result is calculated on the dried basis. The 99.0–101.0% window is narrow, so loss on drying has to be read beside it; a 0.5% water load moves the as-is figure by about half a point.

HPLC answers a different question. It separates the main peak from the rest of the sample, confirms retention time against a standard and allows a peak-purity check with a diode-array detector. If the certificate carries no related-substance line, ask for the chromatogram: a method that resolves the main peak from a neighbouring B vitamin is evidence, while a single assay percentage is not.

The 1:1 salt ratio

Pyridoxine hydrochloride is a 1:1 salt, one pyridoxine molecule to one chloride. The base is 169.18 g/mol; hydrogen chloride adds 36.46, so the salt is 205.64 and chloride is 17.24% of it. The 16.9–17.6% window is about 98–102% of theory.

Read the assay and the chloride as a pair: at 100% assay on the dried basis, chloride must sit near 17.2%; 100% assay with 15% chloride is a different composition. The pair is a consistency check, not an identity test.

The chloride and pH figures prove the salt

The chloride line is an argentometric titration: silver nitrate in a methanol–acetic acid medium with eosin Y, reported on the dried basis at 16.9–17.6%. A certificate with an assay near 100% and chloride at 15% is not the hydrochloride; part of the powder is free base, a non-chloride diluent or another substance.

The pH of the 5% solution, 2.4–3.0, is the second view of the same stoichiometry. A reading above the range suggests free base or an alkaline diluent; below it, excess acid. The chloride line proves the counter-ion, not the base: a different hydrochloride with a similar chloride fraction could sit inside the window, which is why IR and the HPLC retention time are also required.

Where XRD fits, and where it does not

Pyridoxine hydrochloride is crystalline and gives a sharp diffractogram, but XRD is not the release identity test: infrared absorption against a reference is, and chloride and pH close the salt. XRD cannot see water or an amorphous diluent, and it does not quantify.

Its use is narrower: it can show that a disputed lot is crystalline rather than spray-dried, or that a blend carries crystalline lactose, cellulose or another excipient. For routine lots, IR, titration and chloride answer with less equipment, so XRD belongs on request rather than on every certificate.

Three ways a B6 powder can be wrong

Another form of B6. P5P has no chloride and a different molecular weight, IR spectrum and retention time, so it fails the chloride line and the IR comparison before any assay question arises. Pyridoxal and pyridoxamine are closer in structure but give different chromatographic peaks and spectra.

Another B vitamin. Thiamine hydrochloride, niacinamide and riboflavin are plausible additions in a blend. The HPLC profile and the IR spectrum are the practical screens.

A diluent. Lactose, dextrose, starch, silicon dioxide and magnesium stearate all lower the assay, and the inorganic ones raise the residue on ignition above 0.1%. Water is excluded by the dried-basis calculation but visible in the loss on drying. A result of 99.4% with a flat chromatogram and a low residue is coherent; the same assay with an extra peak and a high residue is not.

Writing identity into the specification

An identity clause that can be tested has six parts: the name and CAS number; the reference standard and technique for IR; the assay basis and titration method; the chloride and pH windows; particle size; and a statement that no carrier, diluent or other B vitamin has been added.

Add the evidence clause: the spectrum, chromatogram and chloride result are available for the lot, and the lot code on the certificate matches the pack and the retained sample. A specification can be met by a powder that is not the named substance if identity is reduced to a single assay line.

Five questions for the supplier

  1. Is the material pyridoxine hydrochloride, CAS 58-56-0, and is any free base, P5P or other B vitamin present?
  2. Is the assay on the dried basis by titration, and what is the loss on drying for this lot?
  3. What are the chloride and pH results, and were they run on the same lot as the assay?
  4. Can you send the IR spectrum and the HPLC chromatogram with the peak-purity result?
  5. Who manufactured the lot, and does the retained sample carry the same lot code as the pack?

Five direct answers amount to an identity file. The infrared method is in the FTIR note, and the separation in the HPLC note. The catalog specification is on the vitamin B6 product page; the certificate lines are on the COA page; the forms are compared on the grade page; the release workflow is on the quality page; the retained-sample rule is in the retained-sample entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation