02 Grade comparison

Riboflavin or riboflavin 5-phosphate: choosing a vitamin B2 grade

Technical document 02 · Reviewed 2026-11-18 · Vitamin B2

On this page
  1. Why the two forms are not interchangeable
  2. The two forms side by side
  3. Solubility, crystal and mesh
  4. Which dosage form fits which
  5. What changes when you switch, and how to write it

Vitamin B2 is sold in two supplement forms: riboflavin (CAS 83-88-5), a yellow crystalline powder that is only slightly soluble in water, and riboflavin 5'-phosphate sodium (CAS 130-40-5), a freely soluble salt that carries about 73–79% riboflavin on the dried basis. The two are separate label ingredients with separate specifications and separate content calculations. Within riboflavin itself, the grade question is particle size and granulation; the dosage form and the label decide which one to buy.

In one line

The grade is not a purity ladder: riboflavin and riboflavin 5-phosphate are different label ingredients, and the mesh is a separate decision.

Why the two forms are not interchangeable

Vitamin B2 is a nutrient name, not a single specification. In the EU, Annex I to Directive 2002/46/EC lists the permitted forms as riboflavin and riboflavin 5'-phosphate sodium; the UK schedule carries the same pair; in the US, the Supplement Facts source line names the form after “as”. A certificate that says only “vitamin B2” leaves the form open, and the form is the part that changes the ingredient list, the solubility and the mass of powder that delivers a given amount of riboflavin.

The 98.0–102.0% and 73.0–79.0% figures are not two grades of the same purity. Riboflavin is assayed as riboflavin; the phosphate salt is assayed as its riboflavin content after allowing for the phosphate, the sodium and the water of crystallisation. A figure in the middle of that window is a normal, in-specification result, not a diluted riboflavin. Reading the two windows as a ranking is the most common mistake in a B2 comparison.

The phosphate group at the 5' position is what makes the salt soluble, and what makes it a different molecule with a different CAS number, molecular weight and label name. Neither form is a “more active” version of the other; the vitamin is the same isoalloxazine ring in both.

The two forms side by side

Riboflavin and riboflavin 5'-phosphate sodium · form comparison
PropertyRiboflavinRiboflavin 5'-phosphate sodium
CAS number83-88-5130-40-5
Molecular formulaC17H20N4O6C17H20N4NaO9P (anhydrous)
Molecular weight376.37 g/mol478.33 g/mol anhydrous; 514.36 g/mol dihydrate
Riboflavin content98.0–102.0% on the dried basis73.0–79.0% on the dried basis
Water solubilitySlightly soluble, about 0.08 g/L at 25 °CFreely soluble
Solution appearanceYellow-green with strong fluorescenceYellow with green fluorescence
Label nameRiboflavinRiboflavin 5'-phosphate sodium
Typical formatCapsule, tablet, dry blend, suspensionStick pack, liquid, clear beverage

The molecular weights explain the content gap: riboflavin is 376.37 g/mol, the anhydrous phosphate sodium salt is 478.33 g/mol, and the dihydrate is 514.36 g/mol. The phosphate and the sodium add mass that is not riboflavin, so one gram of the salt delivers less than one gram of the vitamin.

Solubility, crystal and mesh

Solubility is the first practical difference. Riboflavin dissolves to about 0.08 g/L at 25 °C, so a clear beverage at a normal vitamin amount is a slow dissolution problem rather than an impossible one; the crystal dissolves slowly, and fine particles or the phosphate salt are the usual answers. The phosphate sodium salt is freely soluble and can be held as a concentrated stock, which is why it appears in stick packs and liquids. Both solutions are yellow with a green fluorescence, and both are light-sensitive.

The physical grade of riboflavin is set by milling and sieving. The catalog powder is ≥95% through 80 mesh; a 100 mesh milled grade and a granulated grade are available on request. The coarse powder blends well, the finer grade disperses faster, and the granulated grade flows better and makes less dust. None of these changes the assay or the label.

Colour is part of the physical picture. Riboflavin is an intense yellow at low concentration, and the shade varies from yellow to orange-yellow; the phosphate salt is also yellow to orange-yellow and is more likely to take up moisture. A granulated or milled grade can look different without being out of specification.

Which dosage form fits which

A capsule or tablet is the natural home of crystalline riboflavin. The amount per unit is small, so blend uniformity and colour are the practical issues, and an 80 mesh powder with a granulated option covers most processes. A coating can carry the colour, but it does not protect the powder inside from light; the pack does that.

A stick pack, a drink mix or a ready-to-drink beverage is easier with the phosphate salt. It dissolves without a suspension step, and a clear liquid stays clear. If crystalline riboflavin is used in a liquid, the product is a suspension: it has to be shaken, and the particles may settle. A gummy can use either form; the salt is easier in the water phase, the crystal easier to dry-blend.

The dosage form also sets the overage. Riboflavin is lost at the surface of a clear pack and in a hot process, so the label amount and the formula amount are not the same number; the overage should come from stability data, not a rule of thumb.

What changes when you switch, and how to write it

Write the form before the assay. A riboflavin specification names the molecule and the CAS number, then the assay method and basis, then the physical and contaminant lines: “Riboflavin, crystalline, CAS 83-88-5; assay 98.0–102.0% by HPLC on the dried basis; loss on drying ≤1.5%; residue on ignition ≤0.3%; ≥95% through 80 mesh; heavy metals and microbiology as agreed.” A phosphate specification is a different document: “Riboflavin 5'-phosphate sodium, CAS 130-40-5; assay 73.0–79.0% as riboflavin on the dried basis”, plus water content and solubility.

Switching forms changes four things at once: the ingredient name, the formula mass, the solubility of the blend and the colour intensity in the finished product. It does not change the vitamin name on the front of the pack, which is why the switch is easy on paper and hard to defend in an audit. The label and the certificate have to name the same form.

For the same riboflavin content, the phosphate salt adds mass: the anhydrous salt needs about 1.27 times the mass of riboflavin, the dihydrate about 1.37 times. The exact figure comes from the batch COA, because the assay and water content vary within the specification.

The catalog specification sits on the riboflavin product page. The narrow comparison is on the riboflavin versus R5P page; the assay basis is on the COA page; the label rules are on the compliance page; the release test is in the HPLC method note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation