Riboflavin vs riboflavin 5-phosphate: solubility, dose and label
Riboflavin and riboflavin 5'-phosphate sodium are both vitamin B2 on a label, but they are different salts with different solubility, different molecular weight and different content per gram. Riboflavin is only slightly soluble in water and suits capsules, tablets and suspensions; the phosphate sodium salt is freely soluble and suits stick packs, liquids and clear beverages. The switch changes the ingredient name, the formula mass and the label, not just the dissolution step.
The phosphate form buys solubility and pays for it in formula mass and a different label name.
Two forms, two CAS numbers
Riboflavin is the free vitamin, CAS 83-88-5, formula C17H20N4O6, molecular weight 376.37 g/mol. Riboflavin 5'-phosphate sodium is the phosphate ester at the 5' position, isolated as the monosodium salt, CAS 130-40-5; the anhydrous salt is 478.33 g/mol and the dihydrate 514.36 g/mol.
The phosphate and the sodium are why the salt dissolves, and why the two are separate label ingredients: the EU and UK lists name them as two entries under vitamin B2, and the US Supplement Facts source line names whichever form is used. A certificate that says “vitamin B2” without the form has not described either one.
The salt is not a more active vitamin. The isoalloxazine ring is the same in both; the difference is the group on the ribityl chain, which changes solubility, mass and label. A higher assay number does not make riboflavin the better form, and a lower number does not make the salt weaker.
Solubility is the practical difference
Riboflavin dissolves to about 0.08 g/L at 25 °C. A clear beverage at a normal vitamin amount is a slow dissolution problem rather than an impossible one: the amount per serve can sit below the equilibrium solubility, but the crystal dissolves slowly, and fine particles or the phosphate salt are the usual answers. In a capsule or tablet, solubility hardly matters.
The phosphate salt is freely soluble and can be held as a concentrated stock, which is why it appears in stick packs, drops and ready-to-drink beverages. Both solutions are yellow with green fluorescence, and both are light-sensitive, so the salt does not remove the need for an opaque pack.
| Property | Riboflavin | Riboflavin 5'-phosphate sodium |
|---|---|---|
| CAS number | 83-88-5 | 130-40-5 |
| Molecular weight | 376.37 g/mol | 478.33 g/mol anhydrous; 514.36 g/mol dihydrate |
| Riboflavin content | 98.0–102.0% on the dried basis | 73.0–79.0% on the dried basis |
| Water solubility | About 0.08 g/L at 25 °C | Freely soluble |
| Typical format | Capsule, tablet, dry blend, suspension | Stick pack, liquid, clear beverage |
| Label name | Riboflavin | Riboflavin 5'-phosphate sodium |
Content conversion and the label amount
The label declares riboflavin, not the mass of the salt. To deliver a stated amount from the phosphate salt, divide by its riboflavin content: 376.37 divided by 478.33 is about 0.787 for the anhydrous salt, and about 0.732 for the dihydrate. A certificate in the middle of that range gives a slightly different divisor, and the certificate figure is the one to use.
For example, 1.4 mg of riboflavin needs about 1.78 mg of anhydrous salt at the stoichiometric factor, or about 1.84 mg at a certificate figure in the middle of the range. The same 1.4 mg from riboflavin is 1.4 mg of riboflavin, subject to assay and overage.
The overage is separate. It should come from stability data for the finished product and pack, not from the molecular weight; a clear beverage in a clear bottle needs a different overage from an opaque capsule, and solubility does not change light sensitivity.
Both assays need the same basis: riboflavin at 98.0–102.0% on the dried basis, the salt at 73.0–79.0% as riboflavin on the dried basis. If one is as-is and the other dried, the conversion is wrong by the water content.
Which dosage form fits which
A capsule or tablet is the natural home of crystalline riboflavin. The amount per unit is small, so blend uniformity and colour are the issues, and an 80 mesh powder with a granulated option covers most processes. The salt can be used, but it brings sodium and phosphate into the formula and is more hygroscopic.
A stick pack, a drink mix or a ready-to-drink beverage is easier with the phosphate salt, because it dissolves without a suspension step and a clear liquid stays clear. A gummy can use either form; the salt is easier in the water phase, the crystal easier to dry-blend.
A suspension is the one liquid format where crystalline riboflavin is natural: the powder is dispersed, the label says to shake, and the particle size is set for uniformity. A 100 mesh milled grade is available on request. A clear drink made with crystalline riboflavin is a suspension that has not been labelled as one.
What the label must say
In the EU and the UK, the ingredient list names the form and the nutrition declaration gives the amount as a percentage of the 1.4 mg nutrient reference value. In the US, Supplement Facts gives the amount in mg and the percentage of the 1.3 mg Daily Value, and the source line names the form after “as”, for example “Riboflavin (as riboflavin 5'-phosphate sodium)”. The pack, the certificate and the specification must name the same form.
Claims are a separate layer: only claims on the authorised list, with their conditions and wording, and a US structure/function claim needs the DSHEA disclaimer without becoming a claim about a medical condition. This page does not repeat claim wording. The ingredient name is not a claim, but “5'-phosphate” implies a form, and the form has to be the one tested.
The colour is a label fact too. Riboflavin is an intense yellow and the salt is also yellow; in a clear beverage the colour is visible, and in a white capsule it tints the product. If the colour is part of the design, the form and the amount are part of that decision.
When to choose which
Choose riboflavin for a dry dosage form — a capsule, a tablet, a powder blend or a suspension — where the label says riboflavin and the formula does not need a dissolved vitamin. Choose the phosphate salt for a clear liquid, a stick pack, a drop or a concentrate, where solubility is the constraint and the label can name the salt. Choose neither until the label question is settled.
Do not switch forms to chase an assay number. The 98.0–102.0% and 73.0–79.0% windows measure different things, and the second is not a lower grade of the first. Do not switch without changing the label, and do not accept a certificate that names one form for a pack that names the other.
The product page carries the catalog specification, the grade page covers the wider comparison, the compliance page covers the market rules, and the COA page shows how the assay basis is reported.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation