06 Identity & adulteration

How to prove a pyridoxal 5-phosphate lot is P5P

Technical document 06 · Reviewed 2026-11-20 · Pyridoxal 5-Phosphate

On this page
  1. The four identity layers
  2. HPLC and UV: proving the molecule
  3. The phosphorus ratio: proving the phosphate
  4. X-ray diffraction: the solid-state check
  5. What adulteration looks like
  6. How to write the identity into the specification
  7. Five questions for the supplier

A pyridoxal 5-phosphate lot is P5P when four lines agree: the document names the form and CAS number, HPLC retention and UV spectrum match the reference, the phosphorus figure is close to the theoretical value for the hydrate, and the water and assay close the mass balance. The assay alone cannot separate P5P from pyridoxine hydrochloride, from pyridoxal or from a dilution. The phosphate and the water are the direct checks.

In one line

Identity is four agreeing measurements: the document, the HPLC/UV record, the phosphorus figure and the water balance.

The four identity layers

Each layer answers a different question, and none of them covers the others. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of pyridoxal 5-phosphate identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, hydrate formPaperwork only
ChromatographyIs the molecule P5P?HPLC retention, UV spectrum, peak purityThe molecule, not the hydrate
PhosphateIs the phosphate present, one per molecule?Phosphorus by ICP-OESThe phosphate ester
Mass balanceIs it diluted or partly hydrolysed?Assay, loss on drying, related substancesConsistency of the numbers

HPLC and UV: proving the molecule

The HPLC method should name the column, the mobile phase, the wavelength and the standard, and it should resolve P5P from pyridoxal, pyridoxine and pyridoxamine. Identity is retention time plus spectrum. A single peak at the expected time can be a different B6 compound or a degraded standard, so the spectrum is the second dimension rather than a decoration.

The UV spectrum has a condition that many certificates omit: it depends on pH. The absorption maximum sits near 295–299 nm in acidic solution and moves to about 388–390 nm above pH 4; the solution is colourless in acid and yellow as the pH rises. A sample prepared in water at pH 3 and a sample prepared at pH 6 do not give the same spectrum. The method has to fix the diluent and its pH, and a certificate should report the maxima or the ratios it compared, not only “UV conforms”.

The phosphorus ratio: proving the phosphate

P5P has one phosphorus atom per molecule. On the anhydrous free acid (247.14 g/mol) the theoretical phosphorus content is 30.974 ÷ 247.14 = 12.53%. On the monohydrate (265.16 g/mol) it is 11.68%, because the water adds mass without adding phosphorus. A phosphorus result close to one of those figures, read with the loss on drying, is consistent with a P5P lot. A low figure points to dilution or to a B6 form without phosphate; a high figure points to added inorganic phosphate or a different salt.

The vitamin B6 equivalent is the other side of the same ratio: 68.5% for the free acid, 63.8% for the monohydrate and 82.3% for the hydrochloride. A powder that reports a high “vitamin B6” content with no phosphorus is not P5P. The phosphorus and the vitamin B6 figures should tell the same story as the assay and the water.

Chloride is a useful negative check. The catalog specification has no chloride line, and P5P contains no chloride. A chloride result near 17% would point to pyridoxine hydrochloride, while a low result does not prove P5P on its own. Read it with the HPLC retention time and the phosphorus figure.

X-ray diffraction: the solid-state check

X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? It can distinguish the monohydrate from an anhydrous or amorphous solid, and it can compare lots from two sources. It is not a purity assay, and it does not measure the phosphate or the water directly.

Ask for the reference pattern and the detection limit before reading a “match” statement. For a disputed lot, XRD plus phosphorus plus HPLC/UV is stronger than any one of them. XRD is not a routine release test for this product, and a certificate that reports only “XRD conforms” without the pattern has added little. The method is most useful when the question is the solid form rather than the assay.

What adulteration looks like

Common pyridoxal 5-phosphate substitutions and the signals
AdulterantWhat it doesSignalTest
Pyridoxine hydrochlorideCommon B6 source; no phosphateChloride high; phosphorus low; different retentionChloride, phosphorus, HPLC
PyridoxalHydrolysis product; no phosphateExtra HPLC peak; phosphorus lowHPLC/UV, phosphorus
PyridoxamineDifferent B6 formDifferent retention and spectrumHPLC/UV
Inorganic phosphateRaises phosphorus without P5PPhosphorus high against assayPhosphorus, HPLC
DiluentLowers assay and phosphorus togetherAssay low; water or ash highMass balance
WaterRaises loss on drying; lowers as-is assayLOD high; dried-basis assay normalLoss on drying

Colour is the weakest signal. The powder is white to off-white, and the solution colour depends on pH, so a yellow solution is not evidence of degradation by itself. The stronger signals are the phosphorus figure, the UV spectrum run at a fixed pH, and the mass balance.

How to write the identity into the specification

  • “Pyridoxal 5-phosphate monohydrate, CAS 41468-25-1”, or the free acid, CAS 54-47-7, with the hydrate form named.
  • “Assay 98.0–101.0% by HPLC, with the basis stated.”
  • “Loss on drying ≤8.0%, reported on every lot.”
  • “Identification by HPLC retention and UV spectrum, with the diluent pH fixed.”
  • “Phosphorus about 11.7% for the monohydrate or 12.5% for the free acid, by ICP-OES, where the form is to be confirmed.”
  • “No pyridoxine hydrochloride, pyridoxal or other B6 form above the stated limit.”
  • “Particle size ≥95% through 80 mesh; destination market confirmed before the order.”

Five questions for the supplier

  1. Which hydrate form is this lot, and which CAS number is on the certificate?
  2. Can you send the HPLC chromatogram and the UV spectrum, with the diluent and its pH?
  3. What is the phosphorus result by ICP-OES, and what method was used?
  4. What is the loss on drying, and is the assay calculated as-is or on the dried solid?
  5. Is any pyridoxine hydrochloride, pyridoxal or other B6 form present, and will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits; the grades page compares the hydrate forms; the level-four comparison covers the hydrochloride; the HPLC method note explains the separation; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation