Pyridoxal 5-phosphate grades: hydrate, mesh and assay basis
Pyridoxal 5-phosphate is sold as the free acid (CAS 54-47-7, 247.14 g/mol) or as the monohydrate (CAS 41468-25-1, 265.16 g/mol). The two differ by one water molecule, 6.8% of the monohydrate's mass, and that difference moves the assay basis, the weigh-out and the label arithmetic. Mesh and flow are the other grade variables: the catalog grade is an 80 mesh powder, with granulation on request.
The grade decision is the hydrate, the mesh and the assay basis: the monohydrate carries 6.8% water and 7.3% more mass per unit of P5P than the free acid.
Why the hydrate is a grade question
P5P is a pyridine derivative with an aldehyde group and a phosphate ester. The free acid is the anhydrous molecule; the monohydrate holds one water molecule in the crystal. Both are the same active moiety, but they are different solids with different molecular weights and different CAS numbers. A specification that names only “pyridoxal 5-phosphate” has not said which solid is in the drum.
The catalog names the free acid, CAS 54-47-7 and the anhydrous formula, and it allows loss on drying up to 8.0%. That window is wide enough to admit the monohydrate and partly hydrated lots. The certificate therefore has to state the hydrate form and the water result, and the buyer has to decide whether the hydrate is acceptable before the first order rather than after the first weigh-out.
The two P5P forms side by side
| Property | Free acid | Monohydrate |
|---|---|---|
| CAS number | 54-47-7 | 41468-25-1 |
| Formula | C8H10NO6P | C8H10NO6P·H2O |
| Molecular weight | 247.14 | 265.16 |
| Water of crystallisation | None | 6.8% theoretical |
| Phosphorus content | 12.53% | 11.68% |
| Vitamin B6 equivalent | 68.5% | 63.8% |
| Mass for 100 mg P5P | 100 mg | 107.3 mg |
| Typical use | Dry blends where mass is fixed | The usual commercial solid |
The mass row is the one that reaches the balance. A formulator who switches from the free acid to the monohydrate without changing the weigh-out has reduced the P5P in the batch by 6.8%. The reverse switch over-doses by the same fraction. Neither error shows on a certificate that reports only a percentage.
Solubility, pH and handling
P5P dissolves in water less readily than pyridoxine hydrochloride, and its solubility depends on pH. The catalog sets pH 3.0–4.5 for a 1% solution, which is the acidity the material gives in water; a more concentrated stock may need warming, a longer mix or a pH adjustment, because solubility is finite. The solution is not colourless at every pH: it is colourless in acid and turns yellow as the pH rises above about 4. That colour is a pH effect, not a purity signal.
The solid is hygroscopic. The monohydrate already contains its crystal water, but an opened pouch can pick up additional surface water, and the loss on drying rises. Keep the powder in the original foil pouch or an opaque, tightly closed container. Light, especially ultraviolet, is the second handling constraint; a clear jar on a bench is the wrong container for a hold.
Particle size is a finishing grade rather than a chemical one. The standard 80 mesh powder flows and disperses well in a dry blend; a granulated grade reduces dust and improves flow on a high-speed press. Changing the mesh changes the bulk density and the blend behaviour, so it belongs in the order, not in a note after the fact.
Dose arithmetic and the label
The conversion between the forms is fixed by the molecular weights: 265.16 ÷ 247.14 = 1.0729. To deliver 100 mg of P5P free acid, weigh 107.3 mg of the monohydrate. To express a monohydrate result as free acid, multiply by 0.932. These are label and weigh-up calculations, not a dose recommendation.
The vitamin B6 declaration is a second conversion. The pyridoxine equivalent is 68.5% of the free acid and 63.8% of the monohydrate, so 100 mg of either solid declares about 68.5 mg or 63.8 mg of vitamin B6 respectively. The percentage on the certificate is not the vitamin B6 figure: a 99.0% P5P assay still declares the pyridoxine equivalent, and the water and the phosphate are not vitamin B6.
The assay basis is the third number. A lot at 99.0% on the dried solid with 6.8% water is 92.3% as received; a lot at 99.0% as-is is 106.2% on the dried basis. The specification, the certificate and the label should use the same basis, and the water result should travel with it.
What to write into the specification
- “Pyridoxal 5-phosphate monohydrate, CAS 41468-25-1, C8H10NO6P·H2O”, or the free acid with its CAS and formula.
- “Assay 98.0–101.0% by HPLC”, with the basis stated as as-is or on the dried solid.
- “Loss on drying ≤8.0%, measured and reported on every lot.”
- “pH 3.0–4.5 in a 1% solution, with the solvent named.”
- “Identification by HPLC retention and UV spectrum, with the diluent pH fixed.”
- “Particle size ≥95% through 80 mesh; granulated grade on request.”
- “Hygroscopic; store in the original sealed, light-resistant pack.”
We supply the powder at the catalog specification. A switch between the free acid and the monohydrate is a specification change, not a packing choice, and it should be handled through a written change control with the label arithmetic rechecked.
When another grade is the better fit
If the label and the market file are already built on pyridoxine hydrochloride, the hydrochloride is the simpler purchase: it dissolves freely, its assay is on a narrow dried basis, and its entry is a different line in the source list. P5P is not a drop-in for it, and the hydrochloride is not a drop-in for P5P.
If the formula is a dry blend where the P5P mass per unit is fixed, the anhydrous free acid avoids carrying 6.8% water into the calculation. If the formula is aqueous, the monohydrate is usually acceptable once the extra mass is written into the batch record. The choice belongs to the specification, not to the supplier's stock position.
The product hub carries the catalog specification; the level-four comparison sets the two B6 forms against each other; the COA page shows how the hydrate is reported; the compliance page covers the label entries; the identity page gives the tests that distinguish the forms.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation