06 Identity & adulteration

How to prove an inositol hexanicotinate lot is the ester

Technical document 06 · Reviewed 2026-11-20 · Niacin Inositol Hexanicotinate

On this page
  1. The four identity layers
  2. The 6:1 ratio and the hydrolysis arithmetic
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A lot is inositol hexanicotinate when four measurements agree: the document names the ester and the CAS number, HPLC and IR match the reference, hydrolysis gives six moles of nicotinic acid per mole of inositol, and the assay, moisture and impurities close the mass balance. The assay alone cannot separate the ester from a blend with nicotinic acid, inositol or a lower ester.

In one line

Identity is the agreement of four measurements: the document, the HPLC and IR spectra, the 6:1 niacin-to-inositol ratio after hydrolysis, and the mass balance.

The four identity layers

Each layer answers a different question, and a supplier who answers only the first has described the paperwork rather than the powder. The layers are not alternatives; they are checks that should agree.

Four layers of inositol hexanicotinate identity
LayerQuestionTestWhat it proves
DocumentIs the ester named?Name, CAS number, formulaPaperwork only
ChromatographyIs the molecule the ester?HPLC retention and UV spectrumThe intact ester, if the method separates it
SpectroscopyAre the functional groups right?IR spectrum against a referenceEster carbonyl and pyridine rings; no free acid
StoichiometryIs the ratio six to one?Hydrolysis, then nicotinic acid and inositolThe ester composition, not just a nicotinate
Mass balanceIs it diluted?Assay, loss on drying, impuritiesConsistency of the numbers

The HPLC method has to separate the intact ester from nicotinic acid and inositol. A method that hydrolyses the sample first measures total nicotinate and cannot distinguish free acid from the ester; it is a niacin assay, not an ester identity test. Ask for the chromatogram and the retention of the reference standard.

IR adds a different kind of evidence. The ester shows a carbonyl absorption and the pyridine ring, and it lacks the broad acid O–H of nicotinic acid. A spectrum that fits a nicotinate but not the ester reference is a reason to pause, not a cosmetic difference.

The 6:1 ratio and the hydrolysis arithmetic

The ester is built from one inositol and six nicotinic acid units. On complete hydrolysis it yields six moles of nicotinic acid per mole of inositol, and the masses add up with the water that is consumed: 810.72 g of ester plus 108.09 g of water gives 738.66 g of nicotinic acid and 180.16 g of inositol. That is why the two hydrolysis figures sum to about 113% of the ester mass, not to 100%.

The theoretical fractions follow from the same arithmetic. Nicotinic acid is 91.1% of the ester mass and inositol is 22.2%. A laboratory report that shows about 91% nicotinic acid and about 22% inositol is consistent with the ester; a report that shows 91% nicotinic acid and no inositol has measured only half of the molecule.

The ratio is also the adulteration check. A lot blended with free nicotinic acid shows a high nicotinic acid figure and a low inositol figure. A lot made with a lower ester, such as a tri-ester, shows a ratio below six and a different HPLC profile. A lot diluted with a carrier shows a low assay and a mass balance that does not close.

X-ray diffraction: the solid-state check

XRD addresses the solid state rather than the assay: is the solid crystalline, and does its pattern match a reference? A pattern can tell a crystalline ester from an amorphous carrier or a simple blend, and it can compare two suppliers' lots. The diffractogram is silent on purity and on the six-to-one ratio; those questions stay with HPLC and hydrolysis.

Before accepting a “match” statement, ask for the reference pattern and the detection limit. It is not a routine release test here, and a certificate that says only “XRD conforms” has shown little without the pattern. Use it when the dispute is about solid form or a suspected blend; it will not settle an assay question.

What adulteration looks like

Common inositol hexanicotinate substitutions and the signals
AdulterantWhat it doesSignalTest
Free nicotinic acidRaises the niacin figure; adds acidity and water solubilityFree acid peak; ratio above six; low pHHPLC, pH, hydrolysis ratio
Free inositolLowers the ester assay; shifts the ratioInositol high relative to niacinHydrolysis and HPLC or IC
Lower esterMixture of partially esterified speciesMultiple peaks; ratio below sixHPLC profile, hydrolysis ratio
Carrier dilutionLowers the assay; changes loss on drying and ashAssay low; mass balance failsAssay, LOD, ash, microscopy
Another nicotinateSimilar UV, different retention or IRRetention or spectrum mismatchHPLC/UV, IR, XRD

Of the available signals, appearance is the least specific: the white-to-off-white range is broad, and a blend can reproduce it. The stronger signals are the hydrolysis ratio, the IR spectrum and the mass balance. A certificate that reports appearance and assay but not the ratio has left the most likely substitution untested.

How to write identity into the specification

  • “Inositol hexanicotinate, CAS 6556-11-2, C42H30N6O12.”
  • “Assay 98.0–101.0% by HPLC, with the basis stated and the method specific to the intact ester.”
  • “Identification by HPLC retention and IR spectrum against a reference.”
  • “Hydrolysis ratio: six moles nicotinic acid per mole inositol, where the test is required.”
  • “Free nicotinic acid within the agreed limit; loss on drying ≤1.0%.”
  • “Particle size: at least 95% passes 80 mesh; metals and microbiology per the release panel.”
  • “Destination market, label name and niacin contribution confirmed before the order.”

Five questions for the supplier

  1. Which ester is this lot, and which CAS number is on the certificate?
  2. Does the HPLC method separate the intact ester from nicotinic acid and inositol?
  3. Can you provide the IR spectrum and the reference it was compared with?
  4. What is the free nicotinic acid result, and what is the hydrolysis ratio?
  5. If a lot is disputed, would you join a re-test of the retained sample for the hydrolysis ratio and the IR spectrum?

The five answers together are the identity file; one assay figure is not. The specification sits on the product hub; each certificate line is mapped on the COA page; the grade page separates the B3 forms; the level-four comparison follows the label consequences; and the methods library with the FTIR method note explains the spectra.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation