06 Identity & adulteration

How we prove a folic acid lot is folic acid

Technical document 06 · Reviewed 2026-11-18 · Folic Acid

On this page
  1. Four layers, each answering a different question
  2. Reading the IR and UV identification
  3. The chromatogram does the quantitative work
  4. The ratio between the two cleavage fragments
  5. Where XRD would and would not help
  6. Three ways a folate powder can be wrong
  7. Writing identity into the specification
  8. Five questions for the supplier

Identity for a folic acid lot is proved in four layers: the document that ties pack to lot, the infrared and ultraviolet spectra that match the substance, the chromatogram that quantifies it, and, if a result is disputed, an orthogonal technique such as mass spectrometry. The catalog specification requires IR and UV to conform and an HPLC assay of 97.0–102.0% on the anhydrous basis. With the related-substance profile and lot traceability, those tests prove the powder.

In one line

IR says the powder is the right molecule and HPLC says how much of it is there; neither says what else is in the drum, which is why the impurity profile and the lot trail belong to identity too.

Four layers, each answering a different question

What each identity layer proves, and what it cannot
LayerEvidenceWhat it provesWhat it misses
DocumentName, CAS 59-30-3, lot code, certificate, retained sampleThe paper describes this packNothing about the powder
SpectroscopicIR and UV against a reference standardThe functional groups and the chromophore are those of folic acidA few percent of a non-absorbing diluent
ChromatographicHPLC assay and related substancesHow much folate is present, and what else absorbsSpecies with no chromophore at the detection wavelength
OrthogonalLC-MS or NMR on requestMolecular mass and structureNothing; but it is slow and outside a release protocol

The layers are cumulative: an assay result alone is one layer, while a certificate with the spectra and the chromatogram gives three and lets the lot be audited rather than trusted.

Reading the IR and UV identification

The infrared spectrum is a fingerprint: for folic acid, the carbonyl and amide bands of the glutamic acid side chain together with the pteridine ring system, compared against a reference spectrum run under the same conditions. Sample preparation matters: a potassium bromide disc and an attenuated-reflectance accessory give different spectra; extra bands the reference lacks point to a second substance.

The ultraviolet test uses a dilute alkaline solution, where folic acid gives a characteristic absorption spectrum; because it compares spectrum and intensity, a visible dye can leave the ultraviolet region almost unchanged.

Both tests pass for a powder that is 97% folic acid and 3% water, which is why identity cannot be read as a purity statement: IR and UV answer "is this the right molecule", and the assay answers "how much, and what else".

The chromatogram does the quantitative work

The assay is a reversed-phase separation with ultraviolet detection and a reference standard, reported on the anhydrous basis. The same run, read as a peak-area profile, gives the related substances: a total capped at 2.0%, with individual limits for the two degradation products that matter, pterin-6-carboxylic acid and p-aminobenzoyl-L-glutamic acid.

Three things belong in the data package: the retention time of the main peak against the standard, a peak-purity check from a diode-array detector, and the individual impurity results, since 1.9% from one peak differs from 1.9% over six.

The 97.0% floor leaves three percent of room, and a non-absorbing diluent can hide there while the impurity total stays clean. Degradation adds peaks and dilution does not, so a flat impurity profile at 97.4% points to dilution rather than degradation.

The ratio between the two cleavage fragments

Folic acid hydrolyses at the C9–N10 bond, and that single break releases one molecule of pterin-6-carboxylic acid and one of p-aminobenzoyl-L-glutamic acid. The two fragments should therefore appear in roughly equimolar amounts in a lot that has aged or taken up moisture; a large excess of one points to a spiked or residual intermediate rather than storage loss. The same arithmetic applies to the certificate: the anhydrous assay is the as-is result divided by one minus the loss on drying, and the basis has to be stated before comparing with the 97.0–102.0% window.

Where XRD would and would not help

Folic acid is crystalline, so a diffraction scan of the pure substance gives a phase pattern, and different solid forms give different patterns. That makes XRD useful in a solid-state study of polymorphism or a form change after milling, and it can show a crystalline diluent such as lactose. It is not the release identity test: the pattern needs a reference material run under the same conditions, it does not quantify the folate, and an amorphous lot leaves no pattern to read. Identity rests on infrared, ultraviolet and the HPLC assay, with LC-MS or NMR when a peak assignment is disputed.

Three ways a folate powder can be wrong

Another folate. Calcium folinate and the methylfolate salts are separate ingredients with separate label names, and a lot of one sold as the other is mislabelled rather than dilute. The molecular mass, the infrared spectrum and the retention time all differ under a method that resolves the forms; a method validated only for folic acid may report the acid peak and miss a folinate.

A dye. The colour range runs from yellow to orange, easy to imitate and easy to restore on a yellowed lot. A dye shows up as an unexpected peak or a peak-purity failure; ask for the chromatogram, not a photograph.

A diluent. Lactose, dextrose, starch, silicon dioxide and magnesium stearate are plausible additions. Water is excluded by the anhydrous calculation, a non-volatile diluent is not: it lowers the assay and, if inorganic, raises the residue on ignition above 0.3%. That is why the residue belongs next to the assay, and the specification should exclude added carrier.

Writing identity into the specification

A testable identity clause has four parts: the chemical name and CAS number; the reference standards and techniques for the identity tests; the assay basis with its method; and a statement of what must not be present. For this grade that reads as folic acid, CAS 59-30-3, with IR and UV conforming to the reference, assay 97.0–102.0% on the anhydrous basis by HPLC, related substances with individual limits and a 2.0% total, residue on ignition ≤0.3%, and no added dye, carrier or diluent.

Add the evidence clause: the chromatogram, the spectra and the impurity table are available for the lot, and the lot code on the certificate matches the pack and the retained sample. Name the mesh too, because a specification without a particle size does not describe the powder.

Five questions for the supplier

  1. Which folate is this, and is any salt, hydrate, carrier or dye present?
  2. Is the assay reported on the anhydrous basis, and what is the loss on drying for this lot?
  3. Can you send the chromatogram with the peak-purity result and the individual impurity figures?
  4. Were the IR and UV identity tests run against a reference standard, and can we see the spectra?
  5. Who manufactured the lot, and does the retained sample carry the same lot code as the pack?

Five answers amount to an identity file. The tests are summarised in the HPLC method note and the infrared method note. The catalog specification sits on the folic acid product page; the certificate lines are on the COA page; the forms are compared on the grade page; the retained-sample rule is defined in the retained-sample entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation