Folic acid vs methylfolate: form, dose and label
Folic acid and methylfolate are different substances, not two grades of one vitamin. Folic acid is the fully oxidised pteroylmonoglutamic acid; methylfolate is the reduced 5-methyl derivative, supplied as a calcium salt or a glucosamine salt rather than as the free acid. A label declaring 400 µg of folate from either is not declaring the same ingredient or the same mass, and the two sit on separate entries of the EU source list. The choice turns on the label, the dose arithmetic and the stability data in the finished pack.
The two are not interchangeable at the milligram level: the salt, the folate fraction and the label name all change, and a formula built on one cannot simply be relabelled as the other.
What is actually in the drum
| Property | Folic acid | Methylfolate |
|---|---|---|
| Chemical state | Fully oxidised pteroylmonoglutamic acid | Reduced 5-methyl derivative |
| Identity | CAS 59-30-3, C19H19N7O6, 441.4 g/mol | Salt-specific identity; the free acid is not the commercial form |
| Commercial form | Crystalline powder, 80 mesh, no carrier | Calcium salt or glucosamine salt, often on a carrier |
| Assay basis | 97.0–102.0% on the anhydrous basis, HPLC | Expressed as the salt, on the dried or as-is basis |
| Label name | Folic acid | The full salt name |
The assay-basis row is where most comparisons fail: a methylfolate quotation describes a salt whose counter-ion carries no folate, while a folic acid quotation describes the acid itself, so the two percentages have different denominators.
What a microgram of each delivers
Folic acid is its own folate reference: on the anhydrous basis at 100% assay, one milligram of powder is one milligram of folate as the acid. A methylfolate salt is not. Its folate fraction follows from the molecular weight of the salt and the number of water molecules in the hydrate, and it is typically well below the mass of the salt. That fraction, not the assay percentage, is what converts a label claim into a weigh-out.
The second difference is the label unit. In the EU and the UK the declaration is folate in micrograms against a nutrient reference value of 200 µg, so the form has to be converted to folate mass before the percentage is calculated. In the US the declaration is in dietary folate equivalents, and the DFE factor applied to folic acid is not automatically the factor for a methylfolate salt; the current labelling rule and the salt's identity decide the arithmetic. Fix the label number with the regulation in hand, not with a rule of thumb carried over from another product.
The third is the overage: it is set from the loss curve of the specific ingredient in the specific matrix, so an overage carried over from folic acid is not established for methylfolate.
Which one survives the process
As a dry powder in a sealed, light-tight pack, folic acid is the more robust of the two. It is still light-sensitive, and the related-substance profile moves when a lot is exposed, but the crystalline acid tolerates dry storage and direct compression well. The reduced methylfolate is more reactive: it oxidises more readily, and heat and moisture accelerate the loss, which is why the commercial salts and the stabilised grades exist.
The gap widens with the process. A dry capsule or a direct-compression tablet keeps both forms in a low-water environment. A wet granulation, a film coat or a gummy cook puts the ingredient into water and heat, and the reduced form has further to fall. Both need an opaque pack: a clear blister or a transparent stick film is a light-exposure experiment, whichever form is inside.
The practical rule is that the stability data has to belong to the form. A study run on folic acid does not support a methylfolate claim, and a supplier's general statement about "folate stability" is not a matrix result. Ask for the study in the dosage form you will sell, in the pack you will use.
What the label can carry
In the EU, the permitted-source list names folic acid and, by amendment, certain methylfolate salts. Each salt is a separate entry with its own name, so the label has to use the name of the entry that matches the drum. "Methylfolate" alone is not an entry, and a label written for a calcium salt does not cover a glucosamine salt. In the US, the Supplement Facts panel declares folate while the ingredient list names the source; the two forms are separate ingredients, and a product that contains both has to declare both.
The nutrition declaration is not the only line that changes. The ingredient list, the allergen and carrier statements, the storage statement and the claim conditions all follow the source. A claim authorised for folate is tied to the nutrient and to the daily portion, and the register entry is the only wording that can be used.
A form switch is therefore a new label, not an edit: new source name, new unit arithmetic, new overage and, where a carrier is present, a new ingredient-list entry for the carrier as well.
When each one is the right choice
Folic acid is the default when the artwork is already approved, when the product is a dry capsule or tablet, when the destination markets are several and the source list has to cover all of them, and when the buyer's laboratory method is validated for the acid. It is also the simpler file: one identity, one assay basis, one set of degradants.
A methylfolate salt is the choice when the label market permits that specific salt by name, when the formula and the pack have been studied with that salt, and when the analytical method covers it — a method validated for folic acid will not quantify a methylfolate without revalidation. Those are file conditions. A switch made before the file exists is a formula change without a file.
What to write when you switch
Write the specification around the substance, not the vitamin name: the full chemical name with the salt and hydrate, the CAS number for that substance, the assay basis and method, the identity tests, the individual degradants, the water limit, the particle size or carrier, and the label name for each market. Add the statement that the material is a single form, with no other folate source blended in, unless a blend is what the order asks for.
Then test the switch against the arithmetic: folate mass per unit, label percentage, overage and end-of-shelf-life claim. If any of the four cannot be supported by data, the form is not ready to change.
The wider comparison is on the grade page; the catalog specification is on the folic acid product page; the certificate lines are on the COA page; the storage question is on the stability page; the source lists and label rules are on the compliance page; the identity tests are on the identity page. The reference values are in the NRV entry and the daily-value entry.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation