06 Identity & adulteration

How we prove a calcium ascorbate lot is the salt

Technical document 06 · Reviewed 2026-11-20 · Calcium Ascorbate

On this page
  1. The identity layers
  2. The calcium ratio: proving the salt
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A calcium ascorbate lot is the named salt when five signals line up: the document names the dihydrate and CAS 5743-27-1, IR shows ascorbate, calcium lands near 9.4%, the specific rotation sits in the L-form window, and assay, calcium and water reconcile. The assay figure by itself does not distinguish the salt from ascorbic acid, a calcium filler or a diluted lot. Calcium and rotation are the discriminating measurements.

In one line

Identity is the agreement of four measurements: IR for the ascorbate, calcium for the salt, rotation for the isomer and the mass balance for dilution.

The identity layers

A certificate may use the right name without proving the solid. Each layer below answers a separate question and needs separate evidence; an answer to the first question alone describes the paperwork, not the material.

Five checks on a calcium ascorbate lot
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
SpectroscopyIs the anion ascorbate?IR against a referenceThe ascorbate, not the counter-ion
Counter-ionIs calcium present?Calcium by complexometric titration or ICP-OESThe calcium content
IsomerIs it the L-form?Specific rotationThe natural isomer, not erythorbate
Mass balanceIs it diluted or blended?Assay, calcium, water, ashConsistency of the figures

The catalogue identity is IR plus titration. That pair is a workable release check, but it does not count calcium and does not separate the L-form from D-isoascorbate, which reduces iodine in the same way. Calcium and rotation close those gaps.

The calcium ratio: proving the salt

One calcium ion sits between two ascorbate ions. In the dihydrate, C12H14CaO12·2H2O at 426.34, calcium is 40.08 ÷ 426.34 = 9.40% of the mass. The anhydrous salt, at 390.31, carries 10.27%. A catalogue window of 9.0–10.0% therefore fits a mostly dihydrate powder whose drying history varies a little.

The pair can be checked against each other. A lot with 99.5% assay and 9.4% calcium fits the dihydrate. A lot with 99.5% assay and 8.0% calcium does not: 8.0% calcium corresponds to roughly 85% of the salt, so the assay is overstated, the calcium is understated, or something else is in the powder. As a working factor, each 1% of calcium represents about 10.6% of the dihydrate.

Specific rotation checks the isomer. The EU E302 specification gives +95° to +97° at 20 °C for a 5% aqueous solution, as of this review. Erythorbic acid and its salts are the D-form; they consume iodine like ascorbate but rotate differently and are not vitamin C. A titration-only certificate cannot make that distinction.

Complexometric calcium is a quantity test, not a fingerprint. At alkaline pH the magnesium present precipitates, removing the main interference, but the titration still measures calcium rather than the calcium–ascorbate pair. ICP-OES is element-specific and is the result to request when the form is disputed.

X-ray diffraction: the solid-state check

XRD asks whether the solid is crystalline and whether its pattern fits the dihydrate reference. It separates the dihydrate from the anhydrous form and from an amorphous blend, and it can compare two suppliers' lots. It is neither a purity assay nor a counter-ion measurement.

On a disputed lot, XRD, calcium and IR together carry more weight than any single test. XRD is not a routine release test for this material; “XRD conforms” without a pattern or reference adds little. Before accepting a match, ask for the reference pattern and the detection limit. Its main use is a solid-form dispute rather than a potency question.

What adulteration looks like

Common substitutions and their signals
AdulterantWhat it doesSignalTest
Ascorbic acidRaises the iodometric assay; brings no calciumCalcium under 9.0%; pH under 6.0Calcium, pH, IR
ErythorbateSame reducing power, wrong isomerRotation outside the L-form windowSpecific rotation, IR
Calcium carbonateLifts calcium while diluting the ascorbateHigh calcium, low assay, fizzing in acidAssay, ash, acid test
Calcium gluconateCalcium near 9.3%, little ascorbateNormal calcium, low assayAssay, IR, HPLC
DilutionPulls assay and calcium down togetherBoth low; ash or water highMass balance, ash
WaterRaises the water figure, lowers the as-is assayHigh water; normal dried-basis assayLoss on drying

Appearance is the weakest evidence. White to off-white covers a broad range, and oxidation can tint a lot that still passes the titration. Calcium, rotation and the mass balance are the stronger signals. With appearance and assay but no calcium or rotation, the likely substitutions remain untested.

How to write identity into the specification

  • “Calcium ascorbate dihydrate, CAS 5743-27-1, C12H14CaO12·2H2O.”
  • “Assay 99.0–101.0% by iodometric titration; state the basis.”
  • “Calcium 9.0–10.0%; report the method, and use ICP-OES where the form is disputed.”
  • “Identification by IR against a reference; specific rotation within the L-form window where the isomer is a risk.”
  • “pH 6.0–7.5 at 10%; loss on drying ≤2.0%; mesh as agreed.”
  • “No ascorbic acid, erythorbate or calcium filler above the stated limit.”

Five questions for the supplier

  1. Which hydrate form is this lot, and which CAS number appears on the certificate?
  2. What calcium result was obtained, by which method, and does it fit the assay and the water figure?
  3. Will you share the IR spectrum and the specific rotation, not just the assay percentage?
  4. Is the assay on the dried basis or as-is, and how was the basis calculated?
  5. If this lot is challenged, will you re-test the retained sample jointly?

Five clear answers build an identity file; an assay percentage alone does not. The product hub carries the catalogue specification; the COA page shows where each figure sits on the certificate; the grades page compares the forms; the FTIR method note explains the spectrum; the XRD note covers the solid-state check; the vitamin C hub covers the acid.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation