01 COA & batch testing

Calcium ascorbate COA: assay, calcium and the release basis

Technical document 01 · Reviewed 2026-11-20 · Calcium Ascorbate

On this page
  1. The release panel
  2. Assay basis, titration and the calcium figure
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

A calcium ascorbate certificate reports the titration assay, calcium, pH, loss on drying, IR identity, metals, microbiology and mesh. Two of those lines describe the salt: the assay measures the ascorbate, and calcium measures the counter-ion. A certificate that carries only the first has described a reducing powder, not necessarily this product. The ranges in the panel are release gates; the batch COA is the record for the lot in the pack.

In one line

The certificate has to show two numbers that agree: the ascorbate assay by titration and the calcium figure that proves the salt, both tied to a stated basis.

The release panel

The table below reproduces the catalogue limits, not a batch result. Every line needs a method and a boundary before a lot can be judged against it.

Calcium ascorbate release tests and limits
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationIR and titrationConforms to the reference
Assay (as calcium ascorbate)Iodometric titration99.0–101.0%
CalciumComplexometric titration9.0–10.0%
pH (10% solution)pH meter6.0–7.5
Loss on dryingGravimetric≤2.0%
Heavy metals (Pb, As, Cd, Hg)ICP-MS, one result per elementPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
Microbiology (APC, yeast/mould, pathogens)Plate count; absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle size (80 mesh)Sieve analysis≥95% through 80 mesh

Identification tells the reader whether the solid is the ascorbate salt; assay and calcium tell them how much is there. A line that says only “conforms” gives a verdict and withholds the measurement.

Assay basis, titration and the calcium figure

Iodine is the titrant. It oxidises the ascorbate ion, the volume of standard is converted to calcium ascorbate, and the percentage is calculated against a stated basis. Only reduced ascorbate consumes iodine, so dehydroascorbic acid is invisible to the method. The certificate should print the basis beside the percentage: 99.0% dried and 99.0% as-is are different claims about the powder.

Once the basis is known, the arithmetic is direct. A lot at 98.5% as-is with 1.5% loss on drying gives 98.5 ÷ 0.985 = 100.0% on the dried basis. The catalogue writes the formula as the dihydrate, C12H14CaO12·2H2O, and limits loss on drying to 2.0%. Water of crystallisation is part of the formula; the loss on drying is what the test drives off. The certificate should say which water the basis handles.

Calcium comes from a complexometric titration with disodium edetate. Magnesium is precipitated as hydroxide at alkaline pH, so it does not consume titrant, and calcium is titrated to an indicator endpoint. That measures calcium quantity, not the calcium–ascorbate pair. When the salt form is disputed, ICP-OES is the element-specific check.

HPLC is not a release test in the catalogue, but it answers a question the titration cannot. It separates ascorbic acid from dehydroascorbic acid and quantifies the oxidised fraction; ask for it when the colour has moved or when the reduced assay and the appearance disagree.

Release limit versus batch result

The limit sets the boundary for acceptance, and the result is the figure the laboratory obtained from that lot. They should sit in different columns, with the method named alongside. If the result column simply repeats the specification range, the certificate has restated the gate instead of reporting a measurement.

What the result column should contain
ParameterRelease limitResult column
Assay99.0–101.0%A measured percentage, with the titre, standard and basis
Calcium9.0–10.0%A measured percentage and the method, ideally with ICP-OES
pH6.0–7.5 at 10%The measured pH, with concentration and temperature
Loss on drying≤2.0%A measured percentage
Metals and microbiologyPer element; count plus absenceOne figure per element; a count and the absence finding
Particle size≥95% through 80 meshThe measured percentage through the sieve

A reader should be able to reach “passes specification” from the figures themselves. The calcium line deserves a second look: near 9.0% with a high assay it may indicate a partly dried or blended lot, and near 10.0% with a low assay it may indicate an added calcium salt.

What moves between batches

The neutralisation, crystallisation and drying steps shift both pH and the water figure. Calcium follows the form and the drying history, while the assay follows the ascorbate content and the basis. Milling and sieving change the mesh result without touching the chemistry, so a new sieve can move that line while everything else holds.

Appearance is the softest test on the panel. The window runs from white to off-white, and a cream or yellow cast can appear before the titration leaves its range. A darker lot calls for the HPLC result and the water figure before a rejection is decided.

A drift across several lots is more informative than one result close to a limit. If the assay falls while calcium holds, dilution or oxidation is more likely; if calcium falls while the assay holds, free acid or a blend is more likely; a falling pH suggests residual acid, and a rising water figure points to the pack or the store. The same lot code should appear on pouch, drum and retained sample.

When to order an outside test

An outside test is worth ordering when the source is new, the shipment is the first into a regulated market, the salt claim is not supported by the supplier's certificate, or a result is contested. Go beyond a copy of the release sheet: IR for the ascorbate, rotation for the L-isomer, calcium by ICP-OES, HPLC for the ascorbic and dehydroascorbic fractions, water, pH, metals and microbiology.

X-ray diffraction is worth adding when solid form matters, and an ash or chloride check when a different calcium salt is suspected. Each screen should come with its detection limit; “not detected” without that limit describes the method, not the sample.

Keep the chain of custody intact. Test the retained material, identify the lot on the report, and when a result is contested give the referee the sample, the certificate and the specification. Ask for the tests that separate the salt from the acid and from a calcium filler, not another run of the same titration.

What to compare between suppliers

Compare six items: form and CAS number; assay and basis; calcium and method; pH and water; metals, microbiology and mesh; pack and lot code. If two quotations match on 99.5% but disagree on calcium or on the basis, they are probably not describing the same material.

Traceability is the next layer: the manufacturer, the neutralisation and drying steps, and whether the lot code is consistent across pouch, drum and certificate. The product page lists the catalogue limits. The identity page sets out the tests that separate the salt from the acid; the grades page covers the particle options; the compliance page covers the market framework; the complexometric method note explains the calcium titration; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation