02 Grades & mesh

Calcium ascorbate grades: hydrate form, mesh and flow

Technical document 02 · Reviewed 2026-11-20 · Calcium Ascorbate

On this page
  1. Why the grade question comes before the order
  2. The grades side by side
  3. Mesh, flow and the line
  4. Dose arithmetic and the fill
  5. What to write into the specification
  6. When this salt is the wrong grade

Calcium ascorbate is graded on two axes: the hydrate form and the particle specification. The catalogue form is the dihydrate as an 80-mesh powder, with granulation available on request; an anhydrous grade is a separate specification rather than a drop-in. Moving between these grades changes flow, fill weight and the water figure on the certificate, not the identity of the salt.

In one line

A calcium ascorbate grade is the hydrate form plus a particle specification; switching mesh or granulation changes flow and fill, not the chemistry on the label.

Why the grade question comes before the order

A capsule line and a stick-pack line ask different things of the same salt. The capsule needs a powder that flows into a dosator and compacts without sticking; the stick pack needs a powder that dissolves quickly and does not segregate in the blend. Both can be calcium ascorbate and both can meet 99.0–101.0% by titration, yet the two deliveries are not interchangeable on the line.

The hydrate form is the second axis. The catalogue formula is the dihydrate, C12H14CaO12·2H2O. An anhydrous salt carries more calcium and more ascorbic acid per gram, so a form switch moves the label arithmetic even when the assay percentage stays the same. A “buffered vitamin C” product is a third thing again: it is a blend of ascorbates, sometimes with ascorbic acid, and its calcium figure depends on the blend ratio rather than on a grade of this salt.

The grades side by side

Calcium ascorbate grades and what changes
GradeForm and meshCalciumVitamin C equivalentTypical use
Standard powderDihydrate, ≥95% through 80 mesh9.0–10.0%About 82.6%Capsules, tablets, dry blends, sticks
GranulatedDihydrate, agglomerated, coarser9.0–10.0%About 82.6%Flow and dust control; direct compression
Anhydrous (separate purchase)Separate specification; finerAbout 10.3% theoreticalAbout 90.2%Only where the water load must be lower
Buffered blendMixture, not a grade of this saltDepends on the ratioDepends on the ratioA formula decision, with its own label

The vitamin C equivalent is the mass of ascorbic acid the salt supplies: two ascorbate ions per calcium ion, 352.25 g of ascorbic acid per 426.34 g of dihydrate, or 82.6%. The same calculation on the anhydrous salt gives 90.2%. The calcium figures follow the same logic: 40.08 ÷ 426.34 = 9.40% for the dihydrate and 40.08 ÷ 390.31 = 10.27% for the anhydrous form. Rainwood supplies the dihydrate; an anhydrous lot would be a separate purchase with its own specification.

Mesh, flow and the line

Eighty mesh is the finishing cut: at least 95% of the powder passes the sieve. That figure describes the upper end of the particle-size distribution, not the shape of the particles or their flow. Two lots can both pass 80 mesh and behave differently in a hopper, because flow depends on fines, agglomeration and moisture as well as on the sieve cut.

Granulation builds larger, more uniform particles from the fine powder. The assay and the calcium figure do not change; the bulk density, the flow and the dust do. That is why granulation is requested for direct compression, for a blend that must not segregate, and for a plant that cannot control dust from a fine powder. It is a different particle specification and should be written as one.

Dust is also a hygiene question. A fine ascorbate powder disperses easily, and a granulated grade keeps more of the material in the container. Neither grade is “better”; each is a match to the handling system. Ask for the particle-size report and a flow result, not only the mesh line.

Dose arithmetic and the fill

The label conversion starts from the vitamin C figure. One gram of the dihydrate supplies 0.826 g of ascorbic acid equivalent and 0.094 g of calcium. A 500 mg vitamin C dose therefore needs 500 ÷ 0.826 = 605 mg of the salt; the same dose carries 56.9 mg of calcium. A 1,000 mg vitamin C dose needs 1,210 mg of the salt and carries 113.8 mg of calcium.

The reverse direction is the common label error. A label that declares 500 mg of calcium ascorbate delivers 413 mg of vitamin C and 47 mg of calcium. Treating the salt mass as vitamin C inflates the vitamin figure by roughly a fifth. A label that gives the vitamin but omits calcium leaves out a nutrient the customer may count.

Fill weight follows the arithmetic. A capsule that holds 600 mg of a dense powder may not hold 605 mg of a lighter granulation, and a stick pack sized on 500 mg of ascorbic acid needs 605 mg of the salt before any overage. Tablets add a compression question: the dihydrate is soft and hygroscopic enough to need a careful granulation and lubricant choice, and a direct-compression grade may need a coarser particle to run at speed.

What to write into the specification

  • “Calcium ascorbate dihydrate, CAS 5743-27-1, C12H14CaO12·2H2O.”
  • “Assay 99.0–101.0% by iodometric titration; state the basis on the certificate.”
  • “Calcium 9.0–10.0% by complexometric titration; ICP-OES where the form is to be confirmed.”
  • “pH 6.0–7.5 at 10%; loss on drying ≤2.0%.”
  • “Particle size ≥95% through 80 mesh, or the agreed granulation with its own particle-size report.”
  • “Heavy metals and microbiology as listed; pack and retest period named.”

Write the hydrate form into the specification even when the catalogue default is understood. A purchase order that says only “calcium ascorbate” leaves the form, the mesh and the calcium figure open, and the supplier may fill the gap with a material that meets the assay but not the line.

When this salt is the wrong grade

If the formula needs a sharp acid taste, the calcium salt will mute it, and ascorbic acid is the simpler choice. If the label cannot carry the added calcium, or the dose already supplies enough, the salt adds a nutrient the formulator did not plan for. If the application is a clear acidic beverage, the neutral salt changes the pH and may need another acid to rebuild the profile.

If the requirement is a finer powder than the standard mesh, do not assume the 80-mesh grade can be milled at the customer's site without a new particle-size specification; milling changes flow, dust and sometimes the loss on drying. If the requirement is a granulation, order it as a grade rather than as a packing note. The product hub carries the catalogue specification; the level-four comparison covers pH, calcium and the label; the vitamin C hub covers the acid; the sodium salt page covers the alternative counter-ion; the methods library explains the assays; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation