06 Identity & adulteration

How we prove a biotin lot is D-biotin

Technical document 06 · Reviewed 2026-11-18 · Biotin

On this page
  1. Four layers of identity, and the balance
  2. The rotation ratio and the assay basis
  3. When a solid-state method helps
  4. The routes that pass a weak assay
  5. How to write the identity lines
  6. Five questions for a new supplier

A biotin lot is D-biotin only when four lines agree: the document chain, the IR spectrum, the HPLC assay and the specific rotation. The assay says how much material is present, the IR says it is the right molecule and the rotation says it is the right enantiomer. A certificate that reports only an assay has not proved identity, and a lot that passes the assay but fails the rotation is not D-biotin.

In one line

The assay says how much; the IR and the rotation say what, and only D-biotin passes both.

Four layers of identity, and the balance

The identity layers and the supporting mass balance
LayerTestWhat it provesWhat it does not prove
DocumentName, CAS, lot, manufacturer and chain of custodyThe certificate belongs to the packThat the powder is the named substance
FingerprintIR against a reference spectrumThe functional-group pattern matches biotinThe amount, or which enantiomer is present
AmountHPLC assay and retention timeThe concentration and a chromatographic matchThe D/L configuration; a co-eluting substance can pass
ConfigurationSpecific rotation, 2% in 0.1 M NaOHThe optical form is D-biotinPurity on its own; the rotation is not an assay
BalanceLoss on drying and residue on ignitionThe assay is consistent with the volatile and inorganic fractionA separate identity; these are supporting numbers

The layers are not interchangeable. IR is a fingerprint, not a purity test; HPLC is a quantitative method, not a chiral one; polarimetry is a configuration test, not an assay. A supplier who sends only the assay has sent one layer of four.

The rotation ratio and the assay basis

Specific rotation is an enantiomer ratio expressed as an angle. D-biotin rotates plane-polarised light to the right, and the catalog window is +89° to +93° at 2% in 0.1 M NaOH. A racemic DL-biotin would rotate near zero, and a substantially L-enriched lot would fall outside the window. A conventional achiral HPLC assay cannot separate D from L, so the rotation is the release test that answers the configuration question.

The certificate should give the observed rotation, the concentration, the solvent, the temperature and the basis. A rotation without a temperature is not comparable with another laboratory's figure. The same discipline applies to the assay: the 97.5–102.0% window has to be tied to a dried basis or an as-is basis. An as-is result of 102.0% with 1.0% loss on drying would be about 103% on the dried basis, outside the window; both figures can be arithmetically right, but only one matches the specification as written.

Read the assay with the loss on drying and the residue on ignition, not instead of them. The three numbers should reconcile within the method's uncertainty. A high assay with a high residue, or a low assay with a low loss on drying, is a prompt to ask what else is in the powder.

When a solid-state method helps

X-ray diffraction is not the routine release test for biotin; the catalog identity test is IR, and the rotation covers the configuration. XRD becomes useful when the IR is ambiguous, when a supplier claims a specific crystal form or solvate, or when a new source has to be compared with an established reference. The diffraction pattern is a fingerprint of the solid state, and a library match is evidence of similarity, not a quantification of purity.

If XRD is used, ask for the source, the sample preparation and the detection limit for any minor phase. A pattern with no minor peaks is only as informative as the method's sensitivity. For a routine lot, the IR, HPLC and rotation are the working set; XRD is a targeted check, not a substitute for them.

The routes that pass a weak assay

Common identity and content failures, and the test that catches them
RouteWhat the certificate showsTest that catches it
Dilution sold as pureAssay near 1% or 2%, carrier visible in the IRAssay plus IR plus content in mg/g
Under-assay materialAssay below 97.5%HPLC against the specification
DL- or L-enriched biotinAssay may pass; rotation falls outside +89° to +93°Polarimetry
Related substanceAssay may pass; a co-eluting peak is invisibleMethod review and impurity profile
Excess moistureLoss on drying above 1.0%Gravimetric loss on drying

The commercial incentive is usually dilution, not a sophisticated forgery. A 1% blend sold as the pure grade has the appearance of a white powder and an assay that is obviously low only if the certificate is read. The second common failure is a pure-looking certificate with no rotation result, which leaves the enantiomer question open. Neither failure is caught by a single assay.

How to write the identity lines

Identity and release lines to write into a biotin specification
LineMethodLimit or basis
Name and CASDocumentD-biotin, CAS 58-85-5
IdentificationIRConforms to the reference spectrum
AssayHPLC97.5–102.0% (state the basis)
Specific rotationPolarimetry+89° to +93° (2% in 0.1 M NaOH)
Loss on dryingGravimetric≤1.0%
Residue on ignitionGravimetric≤0.1%
Particle sizeSieve analysis≥95% through 80 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

The specification should say D-biotin, not just biotin, and it should state the basis for the assay and the rotation. If the material is a dilution, the pure-material window does not apply: the line becomes biotin content in mg/g, plus the carrier identity and a uniformity result. The grade and the carrier belong in the same document as the identity lines, or the reader cannot tell which product the limits describe.

Five questions for a new supplier

  1. Is the lot D-biotin, and what is the specific rotation, with the concentration and temperature?
  2. Which HPLC method was used, with which detector and which assay basis?
  3. Can you send the IR spectrum and name the reference standard it was compared with?
  4. Is the material pure or a dilution, and if diluted, what is the carrier and the biotin content in mg/g?
  5. Who manufactured the lot, and how does the lot code run from the certificate to the pack?

The catalog identity lines sit on the biotin product page and the certificate is described on the COA page. The grade choice is on the grade page, the fill-weight arithmetic on the pure versus 1% page and the release workflow on the quality page. The IR and HPLC methods are described in the FTIR and HPLC notes.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation