Pure biotin vs a 1% dilution: what the fill weight hides
A capsule fill weight says nothing about the biotin dose. The same 500 mg fill can carry 5 mg of pure biotin at a 1% inclusion or 30 µg from a 1% dilution at a 0.6% inclusion, and both look like a 500 mg capsule. The grade, the inclusion and the label claim are the numbers that decide the dose; the fill weight is only the space.
A 500 mg capsule can hold 5 mg of biotin or 30 µg, and the fill weight looks the same either way.
The arithmetic of pure and 1%
A 1% dilution is 10 mg of biotin per gram, or 10,000 µg/g. To find the mass of dilution for a label claim, divide the claim by 0.01; for a 2% dilution, divide by 0.02. The pure material needs no division: the mass of biotin is the claim. The results are small enough to explain why the grade question exists.
| Label claim | Pure biotin | 1% dilution | 2% dilution | 1% mass as share of a 500 mg fill |
|---|---|---|---|---|
| 30 µg | 0.03 mg | 3 mg | 1.5 mg | 0.6% |
| 100 µg | 0.1 mg | 10 mg | 5 mg | 2% |
| 300 µg | 0.3 mg | 30 mg | 15 mg | 6% |
| 1,000 µg | 1 mg | 100 mg | 50 mg | 20% |
| 5,000 µg | 5 mg | 500 mg | 250 mg | 100% |
At 30 µg the pure material is 0.03 mg, which is not a practical production weigh. The 1% dilution turns the same claim into 3 mg, and the 2% dilution into 1.5 mg; neither is a comfortable direct weigh, which is why a dilution is usually handled as a premix rather than as a single capsule addition. At 5,000 µg the arithmetic reverses: 500 mg of a 1% dilution fills a 500 mg capsule completely, leaving no room for anything else.
What the fill weight hides
The fill weight is set by the capsule size and the powder density. It does not say how much of that powder is biotin, how much is carrier and how much is filler. A 500 mg capsule with 5 mg of pure biotin is 1% biotin and 99% other material; a 500 mg capsule with 500 mg of a 1% dilution is 1% biotin and 99% carrier. The two capsules carry the same biotin but have a different ingredient list, and the fill weight is identical.
The more common case is a low-dose capsule: 100 µg of biotin from 10 mg of a 1% dilution, with 490 mg of filler. The dilution is 2% of the fill by mass, and the biotin is 0.02% of the fill. Nothing on the fill-weight line tells the formulator that the active is a 10 mg inclusion, and nothing on the label tells the consumer that the capsule is mostly excipient. The label claim and the grade are the only two numbers that describe the dose.
Why a small inclusion is a uniformity problem
At a 100 µg claim, the 1% dilution is 10 mg in a 500 mg fill, or 2% by mass. At 30 µg it is 3 mg, or 0.6%. Segregation, electrostatic charge and a mismatched carrier all become visible when the inclusion is this small. The biotin is no longer the powder; it is a minority component dispersed in a carrier, and the carrier is dispersed in the filler.
The control is a premix, not a longer tumble. The carrier's particle size and density should be close to the filler's, the premix should be made in a proportion the blender can disperse, and the blend should be sampled at the top, middle and bottom of the blender and across the fill. A relative standard deviation of 5% or better across the sample points is a common target, agreed in the specification rather than assumed. A 1% dilution is usually a premix, not a finished blend, and a low-dose formula may need a further step-down dilution before the capsule fill.
Capsules, sticks and gummies
For capsules and tablets, the grade follows the fill weight and the claim. A milligram claim can use pure biotin if the fill can carry it; a microgram claim needs a dilution and a premix step. For sticks and drink mixes, the dilution has to disperse in the pack and in the glass, and the carrier has to be one the consumer will accept in the ingredient list. For gummies, the aqueous process, the heat and the pH are part of the grade decision, and the carrier has to survive them.
A dilution is not a solubiliser. Biotin is sparingly soluble in water and soluble in dilute alkali; a 1% dilution on a soluble carrier disperses faster, but it does not raise the solubility of the biotin. In a clear drink, the relevant question is the concentration in the finished volume, not the grade name on the drum.
What the label can and cannot say
The finished label declares biotin in micrograms per portion and the percentage of the nutrient reference value or daily value. It does not declare the dilution weight, the carrier weight or the fill weight. The carrier is an ingredient and belongs in the ingredient list; the grade belongs in the specification and the certificate, not in a consumer claim.
A product made with a 1% dilution cannot be described as pure biotin, and “1%” is not a label claim. The label claim is the biotin mass per portion, and it has to survive the assay tolerance of the destination market. The grade is the supplier's language for what is in the drum; the label is the consumer's language for what is in the portion.
When to choose which
- Choose pure biotin when the claim is in milligrams, the fill can carry the mass, and the plant can disperse a small inclusion through a premix.
- Choose a 1% dilution when the claim is a few hundred micrograms or less and the fill weight is large enough to hold a weighable quantity.
- Choose a 2% dilution when the 1% mass would be too large for the fill or when the premix needs a higher biotin concentration.
- Choose a step-down dilution or a granulated grade when the inclusion falls below about 1% of the fill and the blender cannot prove uniformity.
The decision is arithmetic first, uniformity second and label third. A grade that looks simpler to handle can put less biotin into the capsule if the content and the inclusion are not checked; a grade that looks more convenient can add a carrier the label does not want. The fill weight is the least useful number in the comparison because it is the same for both.
The grade options sit on the biotin product page and the comparison is on the grade page. The certificate lines are on the COA page, the blend risks on the stability page and the pack sizes on the MOQ page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation