02 Grade comparison

Pure biotin or a 1% dilution: choosing a biotin grade

Technical document 02 · Reviewed 2026-11-18 · Biotin

On this page
  1. Why the grade question exists
  2. Pure, 1%, 2% and granulated
  3. Uniformity, particle size and the carrier
  4. What each dosage form needs
  5. What changes when the grade changes
  6. When pure is the right choice

Biotin is supplied as a crystalline powder and as a 1% or 2% dilution, and the grade question is arithmetic before it is commercial. At a microgram label claim, the pure powder is too small to weigh into a capsule, so the dilution supplies the mass that makes the dose measurable and blendable. The grade then changes the specification, the carrier declaration and the uniformity work, not just the number on the assay.

In one line

The grade is set by the micrograms on the label and the milligrams the capsule can carry, not by the assay on the drum.

Why the grade question exists

One kilogram of pure biotin contains about a thousand grams of the vitamin. At a 100 µg label claim that is ten million portions; one kilogram of a 1% dilution contains ten grams of biotin and covers one hundred thousand portions at the same claim. The pure drum is efficient for a high-dose formula and awkward for a low-dose one, because the quantity per capsule is a fraction of a milligram.

A dilution solves the handling problem by adding a food-grade carrier. It does not change the biotin molecule, and it does not make a low dose any less sensitive to mixing. It moves the uniformity question one step upstream, from the capsule fill to the premix, and it adds a carrier that has to be declared and controlled.

Pure, 1%, 2% and granulated

Biotin grades and the mass needed for a 100 µg label claim
GradeBiotin contentMass for 100 µgWhere it fitsWhat to verify
Pure crystalline97.5–102.0% by HPLC0.1 mgMilligram-dose formulas; dry blends with a robust premix stepIdentity, rotation, loss on drying, particle size
1% dilution10 mg/g nominal10 mgMicrogram-dose capsules, tablets and stick packsBiotin content in mg/g, carrier, uniformity
2% dilution20 mg/g nominal5 mgMicrogram dose with a smaller fill or a more concentrated premixBiotin content in mg/g, carrier, uniformity
GranulatedAs agreed on the baseAs agreed on the baseDust control, flow and segregation-sensitive blendsGranule size, carrier, content, uniformity

The conversion is simple and worth writing down. A 1% dilution is 10 mg of biotin per gram, or 10,000 µg/g; one milligram of that dilution carries 10 µg of biotin. A 2% dilution is 20 mg/g. The pure material is not 100%: the catalog assay window is 97.5–102.0%, and “pure” is the grade name, not a purity figure.

Uniformity, particle size and the carrier

A dilution is a blend, and its quality is a mixing result. At a 100 µg claim the 1% dilution is only 10 mg of a 500 mg capsule, which is 2% of the fill; at 30 µg it is 3 mg, or 0.6%. A small inclusion is where segregation, electrostatic charge and a carrier with the wrong particle size show up. The certificate for the dilution should report the biotin content and the carrier, and the supplier should be able to show the mixing record and the uniformity data behind the lot.

The carrier is an ingredient, not packaging. It has to be food-grade, compatible with the other actives and declared on the finished label. Its particle size and density should be close to the rest of the blend, or the premix will separate in the hopper. The pure powder is specified at ≥95% through 80 mesh; a dilution may use a different mesh because the carrier, not the biotin, now sets the flow.

What each dosage form needs

For capsules and tablets, the grade follows the fill weight. A 500 mg capsule can carry 5 mg of pure biotin at a 1% inclusion, so a milligram-dose formula can use the pure grade without a dilution. A 100 µg claim needs 10 mg of a 1% dilution or 5 mg of a 2% dilution, and the rest of the fill is excipient. The smaller the biotin mass, the more the formula depends on a uniform premix.

For powder sticks and drink mixes, the dilution has to disperse in the pack and in the glass. Biotin is sparingly soluble in water and soluble in dilute alkali, so a dilution is not a solubiliser; it is a handling aid. For gummies and chews, the aqueous process, the heat and the pH belong in the grade decision, and the carrier has to be one the process can tolerate. In every form, the label declares biotin in micrograms, not the weight of the dilution.

What changes when the grade changes

The pure-material assay window does not transfer to a dilution. A 1% grade needs a content specification in mg/g, a carrier identity and a uniformity result; its certificate should not be read against 97.5–102.0%. The same switch changes the loss-on-drying limit, the particle-size method, the micro panel and the sampling plan, because the carrier is now the majority of the powder.

The label changes too. The finished product declares the biotin content per portion and the percentage of the nutrient reference value or daily value, and the carrier appears in the ingredient list. “Pure biotin” is not a permitted description of a 1% dilution, and “1%” is a specification term rather than a consumer claim. The grade belongs in the purchase specification, the certificate and the technical data sheet, where the formulator and the auditor can see it.

When pure is the right choice

Pure crystalline biotin is the simpler material when the label claim is in milligrams, when the formula already has a premix step that can handle a small inclusion, or when the carrier would add an ingredient the label does not want. It is also the right reference sample when a dilution is being qualified, because the identity and rotation tests are run on the pure material.

A dilution is the better choice when the dose is in micrograms, when the fill weight is large, or when the factory cannot weigh 0.1 mg accurately and repeatedly. The decision is not about which grade is stronger. It is about which grade puts a weighable, mixable and declarable quantity into the process.

The catalog options sit on the biotin product page. The fill-weight arithmetic is worked through on the pure versus 1% page; the certificate lines are on the COA page; the blend and storage risks are on the stability page; the pack sizes are on the MOQ page. The particle-size term is defined in the glossary.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation