The regulatory file for beta-carotene 10% CWD
A beta-carotene 10% CWD powder can be regulated as a colour preparation, as a nutrient source, or as both, depending on the market and the intended use. In the EU the colour entry is E160a(ii) under Regulation (EC) No 1333/2008, with purity criteria in Regulation (EU) No 231/2012; in the US the colour route is 21 CFR 73.95 and the nutrient route is the GRAS affirmation at 21 CFR 184.1245. The buyer's regulatory team confirms the route for the destination before the label is fixed.
The specification describes the powder; the regulatory file shows the route, the limits and the label for the destination.
What the file contains
A complete file answers four practical questions. What is the material, and which specification version is being bought? Which lot is being released, and what does its certificate report? Which route and label rules apply to the finished product? And what changes if the carrier, the source or the pack changes? The certificate, the technical data sheet and the safety data sheet answer different questions; none answers the route question on its own.
For beta-carotene the route question has two branches. Used for colour, the material is a food additive and the additive entry, the purity criteria and the colour declaration apply. Used for vitamin A, it is a nutrient and the nutrition labelling and supplement rules apply. The same 10% powder can sit on either branch; the use decides, not the product name.
European Union
Beta-carotene is listed as the colour E160a(ii) in Regulation (EC) No 1333/2008. The regulation sets the food categories and maximum levels; the buyer's regulatory team confirms the category that covers the finished product and the level that applies. The purity criteria are in Regulation (EU) No 231/2012, which sets the assay at not less than 96% total colouring matter expressed as beta-carotene, together with the absorbance maxima and the residual-solvent limits.
The 96% criterion is written for the colouring matter, not for a 10% preparation. The preparation has its own beta-carotene content and its carrier, and the buyer confirms how the preparation is covered by the additive entry and how the carrier is declared. For a food supplement, Directive 2002/46/EC and the national implementing rules apply alongside the additive rules.
Labelling follows Regulation (EU) No 1169/2011. Where beta-carotene is declared as vitamin A, the nutrition declaration uses retinol equivalents: 1 µg RE equals 6 µg of all-trans beta-carotene. That conversion is applied to the carotenoid mass, not to the powder mass. Check the current consolidated text and the claims register as of this review.
United States
The colour additive regulation for beta-carotene is 21 CFR 73.95. It permits the additive for colouring foods generally, in amounts consistent with good manufacturing practice, and batches are exempt from certification. The nutrient route is the GRAS affirmation at 21 CFR 184.1245, which covers beta-carotene as a nutrient supplement under the conditions stated there.
A dietary supplement is also subject to DSHEA labelling and cGMP rules. The Supplement Facts panel declares beta-carotene in mcg RAE, and may state the share of vitamin A that comes from beta-carotene. For vitamin A activity, 1 mcg RAE equals 12 mcg of dietary beta-carotene, or 2 mcg of beta-carotene in oil from a supplement; the matrix matters, and a dry dispersion is not automatically covered by the 2:1 factor. The buyer's regulatory team confirms the conversion and the route.
The colour use and the nutrient use are different declarations. Beta-carotene added only as a colour need not be presented as vitamin A; beta-carotene presented as vitamin A has to meet the nutrient labelling rules. A supplier certificate does not choose between them.
Contaminants and purity limits
The release limits below are the catalog specification for the 10% powder. They are ingredient limits; the finished-product calculation is the buyer's. The EU additive specification also sets residual-solvent limits, and those results belong in the file when the powder is sold as a colour preparation.
| Parameter | Catalog limit | What the file should show |
|---|---|---|
| Assay | 10.0–11.0% by UV/Vis | Measured result, with solvent, wavelength and basis |
| Loss on drying | ≤5.0% | Measured percentage for the lot |
| Lead, arsenic, cadmium, mercury | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg | A measured figure per element, plus the finished-product calculation |
| Microbiology | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent | The count and the absence statement for the lot |
| Particle size | ≥95% through 40 mesh | The measured percentage through the sieve |
| Carrier and antioxidant | Declared | The name and the percentage, or a signed declaration |
The 10% assay and the 96% purity criterion are not the same gate. The 10% figure describes a preparation; the 96% figure describes the colouring matter. A specification has to say which article is being bought, because a preparation cannot meet a criterion written for the colouring matter.
Claims and label language
The file makes no disease-related claim for beta-carotene. In the EU, health claims must be authorised under Regulation (EC) No 1924/2006 and listed in the EU register; a vitamin A claim also depends on the finished product meeting the nutrient threshold for a “source” claim. In the US, a structure/function claim must be truthful and not misleading, and a supplement carrying one needs the DSHEA disclaimer. The brand's regulatory reviewer confirms the wording for the product, the form and the market.
The label and the certificate are separate documents. A certificate does not approve a claim, and a claim does not change the specification. A product declaring beta-carotene as vitamin A uses the destination conversion, not the powder weight.
Documents in the file
- Specification with the grade, CAS number and assay basis.
- Batch COA with the UV/Vis result, carrier and antioxidant declaration, contaminants and microbiology.
- Technical data sheet and safety data sheet.
- Allergen, GMO and origin statements; natural versus synthetic origin if the label uses that word.
- Carrier and antioxidant specifications, and residual-solvent results where the additive specification applies.
- Vitamin A calculation for the finished product, if the nutrient route is used.
- Change-control record for the source, carrier, antioxidant and pack.
Where a statement is not available for the lot, the gap should be named before the order, not discovered at the port. A document list with version numbers is more useful than a folder of undated PDFs. The product hub carries the catalog specification; the identity page covers the analytical evidence; the vitamin A page covers the nutrient side; the methods library describes the tests; the quality page describes the release file.
Checklist before the first order
- The grade, CAS number, assay basis and carrier are named in the specification.
- The intended use — colour or nutrient — and the destination market are written on the order.
- The COA, TDS, SDS, allergen, GMO, origin and solvent statements are on file.
- The contaminant results are converted to the finished-product dose.
- The label and the claim have been reviewed for the destination, including the vitamin A conversion.
- The carrier, antioxidant, source and pack are under change control.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation