02 Grade comparison

Beta-carotene pure and the dispersion grades: what changes

Technical document 02 · Reviewed 2026-11-20 · Beta-Carotene Pure

On this page
  1. Why beta-carotene is sold in several grades
  2. The grades side by side
  3. Colour, particle size and handling
  4. Dose arithmetic when you change grade
  5. What to write into the specification
  6. When another grade is the right choice

Beta-carotene is sold as a crystalline colouring matter and as diluted, encapsulated preparations. This product is the crystalline grade, specified at ≥97.0% by UV/Vis; the 10% cold-water-dispersible powder, the 1% powders and the oil dispersions are different specifications with a carrier, a different assay basis and a different label. The grade decides the mass on the scale, the way the pigment disperses and what the finished product declares.

In one line

Choosing a beta-carotene grade is choosing a physical form: the crystal, the 10% dispersion and the 1% powder differ in carrier, assay basis and the mass that carries a dose.

Why beta-carotene is sold in several grades

The crystal is the carotenoid itself: a concentrated, fat-soluble pigment with no carrier. It is the right starting point when the formula already has an oil phase, as a softgel fill or an oil blend does, because the oil becomes the carrier and the crystal dissolves into it. It is also the grade whose assay is closest to a purity figure, which matters when the specification has to stand against a colouring-matter criterion.

The diluted grades solve a different problem. Beta-carotene is intensely coloured, so a dose is a few milligrams, and a few milligrams of a light, dusty crystal is awkward to weigh and almost impossible to disperse in water. A spray-dried preparation divides the pigment into fine particles, protects it with a carrier and an antioxidant, and makes it wettable. The trade is that most of the powder is no longer the carotenoid.

Both approaches are legitimate, and neither is a stronger version of the other. An order that names only “beta-carotene” has not chosen between them.

The grades side by side

Typical beta-carotene grades and what they are for
GradeBeta-caroteneCarrierWaterTypical use
Pure crystal (catalog)≥97.0%NoneNot dispersibleSoftgels, oil blends
10% CWD powder10.0–11.0%Declared carrier plus antioxidantDispersesCapsules, sticks, beverages
10% oil dispersionAbout 10%Vegetable oilNoSoftgel fill, oily foods
1% CWD powderAbout 1%Carrier plus antioxidantDispersesLow-dose colour, dry mixes

The percentages are the carotenoid content of the article, not its purity. The 10% and 1% rows are preparations; the 97% row is the colouring matter, and the 96% figure in the EU additive specification is written for that article. A preparation cannot meet a criterion written for the colouring matter, and the colouring matter cannot do the job of a dispersion.

Colour, particle size and handling

The catalog crystal is a red to orange-red powder with at least 95% passing 80 mesh. It is practically insoluble in water and soluble in fats and organic solvents, so it goes into an oil phase rather than an aqueous one. In a warm oil it dissolves with agitation; in a cold oil it may only suspend, and the mixing time belongs in the process instructions.

An 80 mesh crystal is finer than the 40 mesh of the 10% dispersion, which changes both the colour and the behaviour in the plant. A finer powder looks lighter and more orange because it scatters more light; a coarser crystal looks darker and redder. The finer powder also dusts more, clings to equipment and stains surfaces, and it can carry static. Weighing and transfer should be enclosed where possible.

Colour strength follows the carotenoid mass, not the powder mass. One gram of the crystal carries at least 970 mg of beta-carotene; one gram of the 10% powder carries 100–110 mg. That is roughly a nine- to ten-fold difference, before any difference in isomer profile or carrier colour is counted.

Dose arithmetic when you change grade

The arithmetic is simple and easy to get wrong. To deliver 10 mg of beta-carotene, the crystal at 97.0% needs 10 ÷ 0.97 = 10.3 mg. The 10% powder needs 91–100 mg, depending on whether the lot assays 11.0% or 10.0%. A 1% powder would need about 1 g. The same declared dose therefore means very different fill weights, and a formula switched without recalculating the mass will be out by a factor of about ten.

Carrier mass becomes a fill-weight question in a capsule or tablet. A 10 mg dose taken from the 10% powder arrives with roughly 80–90 mg of carrier and antioxidant, and that bulk has to fit the fill weight and the excipient budget. The crystal adds almost nothing, which is why it fits a softgel whose oil already fills the shell.

Overage is decided separately. Colour and assay fall during storage, and the allowance is set from stability data on the finished formula rather than from the release certificate. Any extra crystal changes the declared amount, so the overage and the label are reviewed as one decision.

What to write into the specification

  • “Beta-carotene, crystalline, CAS 7235-40-7, C40H56, all-trans form.”
  • “Assay ≥97.0% beta-carotene by UV/Vis; state the solvent, wavelength and basis.”
  • “Identification by UV/Vis spectrum against a beta-carotene standard.”
  • “Loss on drying ≤0.5%; particle size ≥95% through 80 mesh.”
  • “Heavy metals and microbiology as listed; colour within the red to orange-red window.”
  • “Residual-solvent statement for the declared manufacturing route.”
  • “Destination market and intended use — colour or nutrient — confirmed before the order.”

A specification that names the grade, the assay basis and the isomer expectation is a purchase specification. One that says only “beta-carotene crystal” leaves the supplier free to choose the solid form and the residual-solvent profile, and the first difference usually appears at the filling line.

When another grade is the right choice

The 10% cold-water-dispersible powder is the practical choice for capsules, stick packs, dry mixes and beverages where a uniform orange dispersion is wanted. It is the wrong choice for a clear oil, for a softgel fill that is already oily, or for a formula that cannot accept the carrier mass or an allergen the carrier may bring.

The 1% powder is for colour work at a very low dose, where even the 10% material would be difficult to distribute evenly through a dry mix. The oil dispersion sits between the crystal and the powder: it is convenient for a softgel line that would rather pump a suspension than weigh a crystal, but it is not a water-dispersible article.

A change in either direction is a new specification, a new dose calculation, a matrix stability check and a label review. The product hub carries the catalog specification; the 10% CWD product page covers the dispersion grade; the level-four comparison takes the assay basis and label question further; the vitamin A page covers the provitamin A conversion; the methods library describes the assay.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation