06 Identity & adulteration

How we prove a fermentation spermidine lot

Technical document 06 · Reviewed 2026-11-20 · Spermidine Fermentation

On this page
  1. The four identity layers
  2. The salt-to-base ratio and the chloride figure
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A fermentation spermidine lot can be called the trihydrochloride only when four records agree: the specification names the salt and CAS 334-50-9, HPLC retention and IR match the reference, the free-base and chloride figures fit the salt, and putrescine is at or below 0.5%. No single assay separates the salt from the free base, an extract or a blend.

In one line

Identity is a set of agreeing numbers: HPLC and IR name the molecule, the free-base and chloride figures name the salt, and putrescine describes the profile.

The four identity layers

A certificate can carry the correct name and still leave the identity unproven. The four records below answer different questions, and each one leaves a gap that another closes.

Four records that establish fermentation spermidine trihydrochloride
RecordWhat it settlesEvidenceLimit of the evidence
SpecificationWhich article is being soldName, CAS, source and versionPaperwork only
ChromatographyWhether the peak is spermidineHPLC retention against a reference; IR spectrumThe molecule, not the salt
Counter-ionWhether the salt is the trihydrochlorideFree-base calculation; chloride by titration or ion chromatographyThe salt form
ProfileWhat else is in the drumPutrescine, cadaverine, loss on drying, mass balanceConsistency of the lot

An answer to the first question alone describes the paperwork, not the powder. A retention time can be matched by a close homologue when the method fails to resolve the neighbouring amines. A carrier can dominate an IR spectrum, and a mass balance can be met by water. The records are read together because each one closes a different gap.

The salt-to-base ratio and the chloride figure

The free base is CAS 124-20-9 at about 145.25 g/mol. The salt, CAS 334-50-9, is about 254.63 g/mol, so 145.25 ÷ 254.63 = 57.0% of the salt's mass is spermidine. What remains is the chloride counter-ion and its proton, not a contaminant. Chloride is about 41.8% of the salt by mass.

Those figures are the arithmetic check on an assay. A 98.0% trihydrochloride is 55.9% spermidine, while a 98.0% free base is 98.0% spermidine. If a quotation or a label uses the two figures as if they were the same, the mass per serving is wrong by more than 40%. A percentage without the form has not said which figure applies.

Water is the other part of the balance. At loss on drying ≤1.0%, a salt at 98.0% leaves little room for related amines and water; assay plus loss on drying plus putrescine should roughly close the mass balance. A gap of several points is a question about what else is in the drum, not a rounding error.

X-ray diffraction and the solid state

X-ray diffraction asks whether the solid is crystalline and whether its pattern matches a reference. The trihydrochloride is crystalline; a spray-dried powder with a carrier, or a blend with maltodextrin, will not match the reference pattern. That makes diffraction useful when the question is solid form or a carrier, not when the question is assay.

Before accepting a “match” statement, request the reference pattern and the detection limit. A report that says “XRD conforms” without the pattern has added little. Diffraction is not a routine release test here; HPLC and IR carry the routine identity, and XRD is for a disputed lot, a new source or a solid-form question.

Fermentation and the salt step can change the crystal habit through drying and milling, so a pattern difference is not automatically adulteration. Read it with the chloride figure, the IR spectrum and the profile before drawing a conclusion.

What adulteration looks like

Substitutions to look for and the signal that catches each
SubstitutionWhat it doesSignalTest
Free base sold as saltAssay passes; free-base fraction and pH differChloride low; free-base figure highChloride, pH, free-base calculation
Wheat-germ extract blended inLowers spermidine per gram; adds extract solidsContent per gram low; IR and LOD shiftAssay, IR, loss on drying, related peaks
Putrescine-rich lotMain peak passes; profile does notPutrescine at or above 0.5%HPLC related substances with a stated LOQ
Dilution with maltodextrin or saltLowers assay; leaves a mass-balance gapAssay low; chloride or LOD oddAssay, LOD, chloride, IR
Non-fermentation sourceSame molecule; different source claimNothing in the assayProcess record and audit

The last row is the one analytics cannot close. A fermentation-derived lot and a lot made by another route can share the HPLC peak, the IR spectrum and the assay. The source is a document and supply-chain question: ask for the manufacturing description, the fermentation declaration and the production site, and keep them with the lot record.

Putrescine and cadaverine sit closest to spermidine: small diamines sharing the same reactive amine groups, and close enough to co-elute when the method was not built to separate them. The method should state the column, how the amine is detected or derivatised, and the quantification limit for each neighbour. A single main peak, with no related-substance section, does not describe the profile.

How to write identity into the specification

  • “Spermidine trihydrochloride, CAS 334-50-9, fermentation-derived, ≥98.0% by HPLC with the detector and basis named.”
  • “Putrescine ≤0.5%, with the method and the limit of quantification; cadaverine reported on request.”
  • “Identification by HPLC retention and IR against a reference.”
  • “Loss on drying ≤1.0%; particle size ≥95% through 80 mesh.”
  • “Chloride about 41.8%, where the salt form is to be confirmed analytically.”
  • “No carrier; if granulated or diluted, declare the carrier and the spermidine content by mass.”

Five questions for the supplier

  1. Which form and CAS are on the certificate, and does the documentation name fermentation as the source?
  2. Which HPLC detector and which basis produced the 98.0%, and is the chromatogram available?
  3. What is the putrescine result and the limit of quantification, and does the method resolve cadaverine?
  4. Is there an IR spectrum against a reference, and a chloride result for the salt?
  5. On a disputed lot, would you join a re-test of the retained sample?

Five clear answers make an identity file; a single percentage does not. The product hub holds the catalog specification, the COA page maps each figure to its line on the certificate, the grades page compares the salt with the other articles, and the level-four comparison covers the source and label consequences. The methods library explains the analytical techniques, and the spermidine product page describes the free base. The release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation