02.1 Free acid vs disodium

PQQ free acid vs disodium: solubility, sodium and the label

Technical document 02.1 · Reviewed 2026-11-20 · PQQ Free Acid

On this page
  1. What the two sodium ions change
  2. Solubility and what it does to the formula
  3. Sodium and the label arithmetic
  4. Dose conversion between the salts
  5. Naming the form on the panel
  6. Choosing a form

Two sodium ions separate the free acid from the disodium salt: the formula weight rises from 330.21 to 374.17 g/mol, the salt contains about 12.3% sodium, and its water solubility is far higher. Those changes reach the label as a different ingredient name, a different mass per serving and a different regulatory citation.

In one line

Adding two sodium ions raises the formula weight by 43.96 g/mol, puts about 12.3% sodium into the powder, makes it water-soluble, and changes the label name and the market file.

What the two sodium ions change

Free acid and disodium salt: the same quinone, a different salt
PropertyFree acidDisodium salt
CAS number72909-34-3122628-50-6
FormulaC14H6N2O8C14H4N2Na2O8
Molecular weight330.21374.17
Sodium contentNoneAbout 12.3%
Catalog assay≥98.0% (HPLC)98.0–102.0% (HPLC, anhydrous)
Loss on drying≤1.0%≤5.0%
Water solubilitySlight; soluble in alkaline solutionsSoluble
Label namePyrroloquinoline quinonePyrroloquinoline quinone disodium salt
EU novel-food entryNot covered by the entryThe form the entry names

The only structural change is the replacement of two acid protons by two sodium ions. The third carboxylic acid group stays as it is, which is why the free acid is still an acid and why it can be dissolved by adding base. The 43.96 g/mol difference is the two sodium atoms less the two protons they replace.

Solubility and what it does to the formula

The free acid dissolves poorly in water on its own. A base removes the acidic protons and the molecule becomes an anion, which is soluble; the liquid turns reddish-brown. The base is a formulation choice with consequences: it introduces sodium or potassium and fixes a pH, and both belong in the label calculation.

The salt needs no base. It dissolves directly and gives the same reddish-brown colour, which is why it dominates aqueous formats such as stick packs and ready-to-drink mixes, and why the commercial specification and the main regulatory entry are built around it. Colour is not a form test, because both forms can produce it.

Solid dosage forms can use either, but the fill weight differs. In a dry blend, the free acid's poor water solubility becomes relevant if the blend is dispersed in water by the consumer. Decide the dosage form first; the form follows.

Sodium and the label arithmetic

The salt is about 12.3% sodium by mass, so 20 mg of it contributes 2.46 mg sodium and 100 mg contributes 12.29 mg. The free acid contributes none from the molecule. That difference can matter in a product where the sodium total is under scrutiny, but it is not the only source: a base used to dissolve the free acid adds sodium or potassium and must be counted.

A sodium-free claim is a separate label decision. It depends on the measured sodium in the finished product, the serving size and the threshold in the market, and it cannot be inferred from the ingredient name. The certificate supplies a number; the claim is a review.

Dose conversion between the salts

Convert with the molecular-weight ratio: 330.21 ÷ 374.17 = 0.8825. To express a disodium quantity as free-acid equivalent, multiply by 0.8825; to go the other way, divide. The ratio comes from the formula and does not change with assay.

Two examples show where the factor is used. If the target is 20 mg of PQQ expressed as free acid and the salt is the source, the weigh-up is 20 ÷ 0.8825 = 22.66 mg of disodium salt. If the label declares 20 mg of disodium salt, the free-acid equivalent is 20 × 0.8825 = 17.65 mg. If the label and the powder are both the free acid, no form factor applies; only the assay and moisture corrections do. These are arithmetic examples, not intake recommendations.

Assay and moisture are a second correction, independent of the form. A dried-basis assay has to be converted to the as-received basis before weighing, and the form factor is applied after that if the label uses the other form. Doing the two steps in the wrong order is a common source of a label that does not match the batch.

Naming the form on the panel

In the EU, the novel-food entry is written for the disodium salt, and that is the position at this review; the entry's authorisation is tied to the salt and its specification. A free-acid ingredient is a different article, and the entry's daily maximum cannot be read across to the acid without a regulatory decision. The buyer's team should confirm the position, and check the current text, before the label is designed.

In the US, the Supplement Facts box carries the ingredient declaration and has to name the dietary ingredient; “PQQ” is not specific enough to distinguish the forms. In GB the register has its own conditions, and Northern Ireland follows the EU list. The panel should carry the form named in the market file, not whichever form the buyer happened to order.

Choosing a form

The free acid is the right starting point when the label names it, when the formulation is non-aqueous or when sodium from the ingredient is unwanted, and when the destination file covers it. The disodium salt is the practical choice for water-based formats and for markets whose file is written around the salt.

Changing from one to the other is a change of specification, not a unit conversion at the balance. It requires a change protocol, a revised specification and a fresh label review. The free-acid product page carries the catalog figures; the grades page places the form in the range; the identity page covers the analytical check; the PQQ disodium page is the other product; the disodium comparison gives the salt-side view; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation