02 Form & grade

PQQ free acid grades: mesh, granulation and the salt question

Technical document 02 · Reviewed 2026-11-20 · PQQ Free Acid

On this page
  1. Why a single form still has grades
  2. The free acid against the disodium salt
  3. Solubility, colour and handling
  4. Dose arithmetic and the dosage form
  5. Specification lines to fix before ordering

PQQ free acid is supplied as a red-orange to brown powder at ≥98.0% by HPLC, loss on drying ≤1.0% and ≥95% through 80 mesh, with granulation available on request. Those options do not change the molecule. The choice is the particle size and flow the dosage form needs, and whether the formula should use the free acid at all instead of the disodium salt.

In one line

The free acid has one chemistry; the grade is the particle size, the granulation and the purity written into the specification.

Why a single form still has grades

PQQ free acid is one chemical entity, so a grade cannot mean a different salt or a different hydrate. What changes between the standard powder and a granulated lot is the particle-size distribution, the flow and the dust. What changes between suppliers is the assay floor, the moisture limit and the impurity profile.

The 80 mesh specification is a finishing decision. A fine powder fills a capsule evenly but can bridge in a hopper and hang in the air; a granulated powder flows better and dusts less, at the cost of a slower dissolution. The catalog offers the 80 mesh powder as standard and granulation on request; the particle-size line moves with the choice.

Assay and moisture are release gates, not grades. A 98.0% lot and a 99.0% lot are the same grade; the second gives the formulator more room in the fill weight, and that is a specification decision rather than a new material.

The free acid against the disodium salt

The comparison that matters most is not between two free-acid powders. It is between the free acid and the disodium salt, because the two are different label ingredients and the names are often used interchangeably in a request.

Free-acid options and the disodium salt they are often confused with
PropertyFree acid, standardFree acid, granulatedDisodium salt
CAS number72909-34-372909-34-3122628-50-6
Assay≥98.0% (HPLC)≥98.0% (HPLC)98.0–102.0% (HPLC, anhydrous)
Loss on drying≤1.0%≤1.0%≤5.0%
Particle size≥95% through 80 meshSet by the granulation≥95% through 40 mesh
SodiumNone in the moleculeNone in the moleculeAbout 12.3% by mass
Water solubilitySlight; soluble in alkaline solutionsSlight; soluble in alkaline solutionsSoluble
Label namePyrroloquinoline quinonePyrroloquinoline quinonePyrroloquinoline quinone disodium salt

Granulation changes the particle size, not the assay or the solubility. The disodium salt changes the identity, the sodium load and the market file. A request that says only “PQQ powder” has not chosen between them.

Solubility, colour and handling

The free acid is slightly soluble in water. It dissolves in alkaline solutions because the acid protons are lost and the molecule becomes the anion; the solution is reddish-brown, and its pH is set by the base used, not by the powder alone. A formulator who raises the pH to dissolve the free acid is making the salt in the vessel, and the sodium or potassium from that base is now part of the formula.

In the dry state the powder is a red-orange to brown solid. The colour window is wide and covers fermentation and drying variation; it is not an assay. The 80 mesh powder is fine enough to dust, so handling needs containment and the pack stays closed between uses. Light is a second handling issue: the powder belongs in the foil pouch or an opaque container, not a clear jar.

Bulk density and flow are not on the catalog certificate. If the capsule machine or the blend line needs a number, ask for it as a separate measurement taken on the lot you will use; a value from another lot is a starting point, not a release result.

Dose arithmetic and the dosage form

When the label declares the free acid, the weigh-up uses the free acid and the assay correction only: 20 mg declared at 98.0% assay needs 20 ÷ 0.98 = 20.41 mg of powder. When the label declares the disodium salt but the formula uses the free acid, the label and the powder no longer describe the same ingredient, and the conversion factor 0.8825 cannot repair that.

Going the other way, 20 mg of disodium salt carries 17.65 mg of free-acid equivalent. A formula built on 22.66 mg of disodium salt for a 20 mg free-acid declaration needs 20 mg of the free acid, not 22.66 mg, because the sodium has been removed from the mass.

The dosage form decides the grade. A capsule or tablet takes the 80 mesh powder, or the granulated form if flow is the constraint. A dry blend takes either, but a granulated powder segregates less. A clear drink is a poor fit for the free acid: the low water solubility and the alkaline pH needed to dissolve it both become formulation problems.

Specification lines to fix before ordering

  • “Pyrroloquinoline quinone, free acid, CAS 72909-34-3, C14H6N2O8.”
  • “Assay ≥98.0% by HPLC; the basis, as-is or dried, is stated on the certificate.”
  • “Loss on drying ≤1.0%.”
  • “Sodium reported; the free acid carries no counter-ion.”
  • “Particle size ≥95% through 80 mesh; granulation only by written agreement.”
  • “Heavy metals and microbiology as listed; residual solvent where the process uses one.”
  • “Light-resistant pack; storage condition and retest period stated.”
  • “Destination market and label name confirmed before the order.”

The product page carries the catalog figures. The free acid against disodium comparison takes the solubility and sodium questions further, the identity page covers the tests that separate the forms, and the PQQ disodium page is the other product, not another grade.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation