01 COA & batch testing

What the COA for sodium hyaluronate actually contains

Technical document 01 · Reviewed 2026-11-19 · Hyaluronic Acid

On this page
  1. The certificate as a line-by-line report
  2. What the 91% and 44% figures measure
  3. The molecular-weight line
  4. Release limit versus batch result
  5. What moves between batches
  6. When to order an outside test
  7. What to compare between suppliers

Sodium hyaluronate (CAS 9067-32-7) is a linear glycosaminoglycan, and its certificate is not a single purity figure. A usable COA reports appearance, sodium hyaluronate by HPLC, glucuronic acid by UV, molecular weight, pH, protein, loss on drying, particle size, the heavy-metal panel and microbiology. Each line needs a method, a release limit and a stated basis; the catalog ranges sit on the product page, while the batch COA is the record for one lot.

In one line

A sodium hyaluronate certificate only identifies the lot when the assay, the glucuronic acid figure and the molecular weight are reported on stated bases with named methods.

The certificate as a line-by-line report

A COA earns its place in a supplier file when a reviewer can reconstruct the release decision from the page. That takes three columns: what was measured, how, and the release limit. A certificate that prints only “conforms” moves the decision back to the supplier.

Identity, assay and solution parameters · sodium hyaluronate
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
Sodium hyaluronateHPLC≥91.0%
Glucuronic acidUV or colorimetric method≥44.0%
Molecular weightSEC-MALLS or viscometry1.0–1.5 MDa
pH (1% solution)Potentiometry6.0–7.5
ProteinColorimetric or UV≤0.1%

The second block covers handling and contamination.

Physical, contaminant and microbiological limits
ParameterMethodRelease limit
Loss on dryingGravimetric≤10.0%
Particle sizeSieve analysis≥95% through 80 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

What the 91% and 44% figures measure

Sodium hyaluronate is the sodium salt of a repeating disaccharide of glucuronic acid and N-acetyl-D-glucosamine. The sodium salt repeat unit has a formula mass of about 401 g/mol, and glucuronic acid is about 43.9% of that mass. The ≥44.0% line therefore sits at the stoichiometric ceiling for the dry salt, not at an arbitrary impurity threshold.

That arithmetic makes the basis decisive. If 91.0% sodium hyaluronate and 44.0% glucuronic acid were both reported as-is mass fractions, the glucuronic acid would be about 48% of the polysaccharide, which the repeat unit cannot supply. The results reconcile only when one is on the material as sold and the other on the dried polysaccharide, or when the methods use different standards. The certificate should print the basis and standard beside each result; the reviewer should not divide one by the other until they match.

Protein and nucleic acid are the other side of purification. Protein is capped at ≤0.1%; it is residual fermentation or tissue material, it contributes nitrogen and UV absorbance, and it is not hyaluronan. Nucleic acid is a separate residue from the production organism and belongs in the file as a result, even where the catalog prints no limit. A low protein figure with no nucleic acid result answers half the question.

Loss on drying is water, not hyaluronate. A lot near the moisture ceiling carries less dry matter than a dry lot, and its 91% assay rides on more water. pH is measured at 1% in water; it picks up residual acid or alkali and sets the window in which the chain is stable.

The molecular-weight line

Molecular weight is a distribution, not a single molecule. The catalog range is 1.0–1.5 MDa, an average for the grade; a batch can sit anywhere in that window and still be the grade, while the distribution around it can differ. The certificate should name the method — SEC-MALLS, or viscometry with a declared Mark–Houwink relationship — because the two do not report the same average.

A number without a method cannot be compared with a competitor’s number or a previous lot. “Low molecular weight” is relative too: the specification has to state the range and the method. The grade page sets out the working bands.

Release limit versus batch result

The release limit is the gate; the batch result is what was measured. They belong in separate columns. A result column filled with the specification range is not a result, it is a copy of the gate, and it hides drift until a lot fails.

Some lines need more attention. Sodium hyaluronate near 91.0% and glucuronic acid near 44.0% sit at the edge of what the material can be, so a result at the limit deserves the raw data. Loss on drying near 10.0% reduces dry matter and shelf-life margin. Molecular weight near either end of 1.0–1.5 MDa changes viscosity at the same concentration, which is a formulation fact even when the lot is released.

“Passes specification” is a conclusion. The buyer should be able to reach it from the page.

What moves between batches

Fermentation batches move in molecular weight, protein and colour; purification and drying move moisture, pH and particle size. A molecular weight that drifts downward across lots can come from a longer hold, a hotter drying step or a different recovery step, and the assay may stay inside its window while the viscosity falls.

Colour and odour are less quantitative and often more revealing. A yellow or tan tint can point to a hot dry, residual medium or trace metal; a sour or fishy odour can point to a fermentation residue or an animal source. Neither is a specification line, but both are reasons to open the batch record.

Read the trend, not one certificate.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a molecular-weight claim the certificate does not prove, or a disputed result. The useful panel is not a full repeat: HPLC with UV detection, a glucuronic acid assay, SEC-MALLS, FTIR, ICP-MS and microbiology, all on one submitted sample.

Ask the laboratory to report its detection limit and its calibration standard. A “not detected” line without a limit is evidence about the method’s sensitivity, not about the sample. The same principle applies to the sodium hyaluronate assay: the report should name the column, the detector, the standard and the basis, not only the percentage.

An outside laboratory is also the referee when a result is contested. Give it the retained sample, the supplier’s certificate and the specification, and keep the chain of custody tied to the lot code.

What to compare between suppliers

Put six lines side by side: source route; sodium hyaluronate result, method and basis; glucuronic acid result, method and basis; molecular weight result and method; protein and nucleic acid; moisture and pH. Two quotations that agree on the assay but diverge on the other five are not describing the same powder.

The second layer is traceability. The lot code should match on certificate, drum and retained sample. The certificate should name the manufacturer, the source route and the drying and milling steps; a correct certificate can still belong to another drum.

The catalog specification sits on the sodium hyaluronate product page. The identity tests are on the identity page, the release workflow on the quality page, and the HPLC method note at HPLC for ingredient identity. The moisture line is defined in the loss-on-drying entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation