02 Grade comparison

High, medium or low molecular weight: choosing a hyaluronic acid grade

Technical document 02 · Reviewed 2026-11-19 · Hyaluronic Acid

On this page
  1. Why molecular weight is the grade decision
  2. High, medium and low bands side by side
  3. Content, viscosity and solubility
  4. Capsules, sticks and beverages
  5. What changes when you change grade
  6. Writing the grade into the specification

Sodium hyaluronate is sold in molecular-weight bands, and the catalog grade on this page is 1.0–1.5 MDa. The band, not the ≥91.0% assay, decides the viscosity at a given solids level, which dosage forms fit, and what the label can support. A lower-molecular-weight grade is available on request; it carries the same CAS number 9067-32-7 but a different specification.

In one line

The molecular-weight grade, not the headline assay, decides the viscosity, the dosage form and what the label can support.

Why molecular weight is the grade decision

Hyaluronan is a polymer, not a single molecule. The same repeating disaccharide can be assembled into chains of very different length, and the chain length changes the hydrodynamic volume the molecule occupies in water. The assay measures the mass of polysaccharide in the sample; it does not measure how long the chains are. Two lots that both report ≥91.0% can behave differently in the same formula when one is 1.4 MDa and the other is 0.3 MDa.

The words high, medium and low are commercial descriptions, not a legal classification. A supplier’s “high” may begin at a different point from another supplier’s, and a certificate that says only “high molecular weight” cannot be compared with anything. The specification has to carry a numeric range and the method that produced it. The bands below are the working definitions used on this page, not a pharmacopoeial standard.

The grade is also the first thing to settle in a formulation project. Capsule size, stick weight, mixing time and the clarity of a drink all depend on it. Changing the grade after the artwork is approved means repeating the formula and the stability work.

High, medium and low bands side by side

Working molecular-weight bands for sodium hyaluronate
BandMolecular weightViscosity at equal solidsWhere it usually fits
High≥1.0 MDa; catalog 1.0–1.5 MDaHighestCapsules, tablets and low-solids sticks
Medium0.1–1.0 MDaModerateSticks, tablets and mixed formats
Low<0.1 MDaLowestHigher-solids drinks and small sachets

The table is qualitative on purpose. Viscosity depends on concentration, temperature, shear rate and the measurement system as well as on molecular weight, so a viscosity figure without those conditions is not a specification. If viscosity matters to the filling line, write it into the specification with the concentration, temperature and spindle or shear rate.

Content, viscosity and solubility

At the same concentration, a higher-molecular-weight chain occupies more volume and gives a more viscous solution. A formulator can reach a target viscosity with less high-molecular-weight solids, or with more low-molecular-weight solids. That trade is the practical meaning of the grade: it decides how much powder fits into a capsule, a stick or a bottle at a workable thickness.

All three bands are soluble in water, but they do not dissolve at the same speed. A high-molecular-weight powder wets slowly and can form lumps if it is added too quickly; a low-molecular-weight powder dissolves faster and is easier to bring to a clear solution. The 80 mesh particle size helps dispersion and blending, but it does not change the chain length. A granulated grade, available on request, changes flow and dusting rather than molecular weight.

The catalog sets sodium hyaluronate ≥91.0%, glucuronic acid ≥44.0%, protein ≤0.1%, loss on drying ≤10.0% and pH 6.0–7.5 in 1% solution. Those limits apply to the grade on this page; a low-molecular-weight grade is quoted against its own specification, and the assay alone does not distinguish it. The COA page explains how the assay and moisture figures interact.

Capsules, sticks and beverages

A capsule or tablet has a fixed volume, so the grade and the amount per serving have to be decided together. A high-molecular-weight grade usually needs less material to build viscosity, but it also hydrates slowly; a low-molecular-weight grade needs more material for the same thickness but disperses faster. The right choice depends on the fill weight and the process, not on a general rule about which grade is better.

A powder stick is a dry blend until the consumer adds water. The grade affects how quickly the stick disperses and how thick the drink becomes. A high-molecular-weight grade at a low dose can give a clean, light-bodied drink; a low-molecular-weight grade at a higher dose can keep a small sachet within a workable volume. A functional beverage is the most demanding format because clarity, viscosity and solids all compete in one bottle; a low-molecular-weight grade is often the easier starting point when the solids load is high.

None of this is a health claim. The format decision is about physics and fill weight: how the powder wets, how the solution flows, and how much material fits in the unit the customer will use.

What changes when you change grade

A grade change is a specification change even when the CAS number stays the same. The molecular-weight range and method change, the viscosity at a given solids level changes, the dissolution time changes, and the stability study has to be repeated in the new matrix. A capsule study with a high-molecular-weight grade does not support a low-molecular-weight stick, and a beverage study does not support a tablet.

The label can change too. If the artwork names a molecular-weight grade, the claim has to be supported by the batch COA and by the method behind it. If the label says only “sodium hyaluronate”, the grade is still a specification term, and the buyer should be able to trace which grade the lot was released against. The high versus low comparison narrows the decision to the two ends of the range.

Commercial terms move with the grade as well: a low-molecular-weight grade may be a separate production run with its own lead time and pack. The ordering page covers the pack and lead-time questions, and the stability page covers the study that a grade change triggers.

Writing the grade into the specification

A grade line needs a number, a method and a source route. “High molecular weight” alone is not a specification. A workable line reads: sodium hyaluronate ≥91.0% by HPLC; glucuronic acid ≥44.0% on the dried basis; molecular weight 1.0–1.5 MDa by SEC-MALLS; protein ≤0.1%; loss on drying ≤10.0%; pH 6.0–7.5 in 1% solution; ≥95% through 80 mesh; heavy metals and microbiology to the listed limits; source route declared. For a low-molecular-weight grade, replace the range and keep the rest of the structure.

The label name is a separate decision. The ingredient is sodium hyaluronate, and a molecular-weight description is a specification or a claim, not a required part of the ingredient name in the EU, US or UK. If the brand wants the grade on the front of the pack, the regulatory team should confirm the wording for the destination market and the COA should be able to support it. The identity page shows how the molecular-weight line fits the rest of the identity file, and the catalog specification is on the product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation