06 Identity & adulteration

How we prove a chitosan lot is chitosan

Technical document 06 · Reviewed 2026-11-19 · Chitosan

On this page
  1. The four identity layers
  2. The deacetylation ratio and the nitrogen cross-check
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A chitosan lot is identified by four agreeing measurements: the document names the material and its source, titration gives the degree of deacetylation, viscometry gives the chain length, and the solubility behaviour separates chitosan from chitin. Ash, insoluble matter and moisture close the balance. No single figure proves identity, because the material is defined by a ratio of repeat units rather than by an assay.

In one line

Chitosan is proved by what dissolves and what does not: the acid-soluble fraction carries the free amine, and titration, viscosity and ash have to agree with the source.

The four identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of chitosan identity
LayerQuestionTestWhat it proves
DocumentIs the material and its source named?Name, CAS 9012-76-4, formula, source recordPaperwork only
DeacetylationIs the acetyl fraction low enough?Titration, with NMR as the reference methodChitosan rather than chitin
SolubilityDoes the free amine protonate?Dissolution in 1% acetic acid; insolubility in water and alkaliThe behaviour of a deacetylated polymer
Chain lengthWhich viscosity grade is it?Viscometry at 1% in 1% acetic acidConsistency with the declared grade
Mass balanceIs it diluted or contaminated?Moisture, ash, insoluble matterConsistency of the numbers

The deacetylation ratio and the nitrogen cross-check

Degree of deacetylation is a ratio: the number of glucosamine units with a free amine divided by the total number of units. The titration measures the free amine directly after the polymer is dissolved, which is why the dissolution step has to be complete before the endpoint is read. Proton NMR measures the acetyl protons against the anomeric protons and is the reference method; the two methods can differ by a few points on the same lot.

Nitrogen gives an independent check on the same ratio. Every repeat unit carries one nitrogen whether or not it carries an acetyl group, but the acetyl group adds mass, so the nitrogen percentage falls as the acetyl content rises. A fully deacetylated chitosan is about 8.7% nitrogen, a lot at 85% deacetylation is about 8.4%, and chitin is about 6.9%. A nitrogen figure near 8.4% is consistent with an 85% claim; a figure near 7.5% suggests a lot closer to chitin or a diluted material, and the titration should be repeated with the NMR reference before the lot is accepted.

Nitrogen by Kjeldahl is not a release test here, and it does not replace the titration. It is the arithmetic check that catches a certificate whose deacetylation figure and composition cannot both be right.

X-ray diffraction: the solid-state check

X-ray diffraction answers a different question: what crystalline order does the solid have? Alpha-chitin gives relatively sharp reflections near 9° and 19° two-theta, while a deacetylated chitosan shows a broader pattern with a strong reflection near 20° and a weaker one near 10°. The loss of the chitin reflections and the broadening of the pattern are consistent with deacetylation, and the degree of crystallinity also depends on the source, the drying step and the residual moisture.

XRD is not a release test for this product, and a certificate that says only “XRD conforms” without a pattern or a reference has added little. It is useful when the question is solid form: a highly crystalline lot and an amorphous lot of the same deacetylation behave differently in a mill and in a capsule fill. Ask for the pattern, the reference and the detection limit behind any match statement.

What adulteration looks like

Substitutions and the signals that catch them
AdulterantWhat it doesSignalTest
Under-deacetylated chitinLowers the free-amine count; raises insoluble matterDeacetylation low; insoluble matter high; nitrogen lowTitration, insolubles, nitrogen
Starch, maltodextrin or glucoseDilutes the polymer; feeds browning in a blendNitrogen low; viscosity low; iodine reactionNitrogen, FTIR, viscosity
Silica or saltAdds weight that does not dissolveAsh high; insoluble matter highAsh, ICP-OES
Another hydrocolloidMatches the viscosity, not the chemistrySolution behaves differently; IR bands differFTIR, NMR, acid solubility
WaterRaises the as-is weight; lowers the effective gradeMoisture high; powder cakesMoisture, appearance

Appearance is the weakest signal. Off-white to pale yellow covers a wide range, and a darker lot can be a legitimate drying difference or a different source. The stronger signals are the deacetylation figure with its method, the nitrogen cross-check, the ash and the insoluble matter, because those four move together when the material is not what the label says.

How to write identity into the specification

  • “Chitosan, CAS 9012-76-4, (C6H11NO4)n, source named.”
  • “Degree of deacetylation ≥85% by titration; method stated on the certificate.”
  • “Viscosity 50–200 mPa·s at 1% in 1% acetic acid, with temperature and standing time.”
  • “Soluble in dilute acetic acid; insoluble in water and in neutral or alkaline solutions.”
  • “Moisture ≤10.0%; ash ≤1.0%; insoluble matter ≤1.0%; ≥95% through 80 mesh.”
  • “Nitrogen and XRD reported where the identity is disputed.”

Five questions for the supplier

  1. Which source is this lot, and what does the allergen statement say?
  2. Which titration method produced the deacetylation figure, and can you provide the NMR reference result?
  3. What are the viscosity conditions, and how long did the solution stand before it was measured?
  4. What are the ash and insoluble-matter results for this lot?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file; a single deacetylation percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the level-four comparison sets chitosan against its parent polymer; the methods library covers the instruments; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation