Chitosan grades: the two numbers that define the powder
Chitosan is traded by grade, and a grade is fixed by two numbers: degree of deacetylation and viscosity. The catalog grade is ≥85% deacetylation by titration and 50–200 mPa·s in 1% acetic acid, a low-viscosity, high-deacetylation powder milled to 80 mesh. The form, powder or flakes, is the third variable, and it changes hydration time rather than chemistry.
A chitosan grade is a pair of numbers, deacetylation and viscosity; the purchase order that names only the first has not described the material.
Why chitosan is graded at all
Chitin is a polymer of N-acetylglucosamine, and chitosan is what it becomes when part of the acetyl groups are removed. The conversion is never complete, so every commercial lot sits somewhere on a continuum between the two. The first number, degree of deacetylation, says how far along that continuum the lot has travelled: it sets the number of free amine groups, the charge density in acid solution and the point at which the polymer becomes soluble.
The second number, viscosity, says how long the chains are. Two lots can carry the same deacetylation figure and behave like different materials in a mixer: one pours and the other gels. Viscosity is therefore part of the grade, not a processing detail.
Source is the third axis. A shrimp-shell lot, a crab-shell lot and a fungal-fermentation lot can meet the same two numbers and still differ in ash, colour, odour and the documents that travel with them. Food grade and technical grade are a fourth distinction: the polymer may look the same on the certificate, while the contaminant panel and the traceability file are not.
The grade families side by side
| Grade family | Deacetylation | Viscosity (1% in 1% acetic acid) | Form | Where it fits |
|---|---|---|---|---|
| Catalog, food grade | ≥85%, titration | 50–200 mPa·s | 80 mesh powder; flakes on request | Capsules, tablets, powder blends |
| Higher-viscosity food grade | ≥85% | Above 200 mPa·s, agreed per lot | Powder | Thicker solutions, film-forming |
| Higher-deacetylation grade | 90–95%, agreed per lot | Agreed per lot | Powder | Where the free-amine count is the point |
| Flake grade | ≥85% | 50–200 mPa·s | Flakes | Stock solutions; slow hydration |
| Fungal source | ≥85%, agreed per lot | Agreed per lot | Powder | Where a crustacean-free source is required |
| Technical grade | Not specified for food | Wide range | Flakes or powder | Non-food uses; not a substitute for food grade |
The table is a map, not a catalogue. Only the first row is the grade specified here; the others are quoted against an agreed specification. What matters commercially is that both headline numbers sit on the same certificate and the same lot. A quotation that states deacetylation and leaves viscosity to the packing list has described half a grade.
Solubility and what the powder does in the mixer
Chitosan does not dissolve in water. The free amine has to be protonated first, which is why dilute acetic acid is the standard solvent and why the catalog note says soluble in dilute acetic acid, insoluble in water and in neutral or alkaline solutions. In 1% acetic acid the polymer becomes a polycation and the solution clears; raise the pH towards neutral and it comes back out.
Viscosity decides how much solid can be dissolved and how the solution behaves. A 50–200 mPa·s lot can be taken to a few percent solids with ordinary stirring; a lot above 200 mPa·s thickens sooner and traps air. Flakes hydrate slowly and usually need an overnight soak, while an 80 mesh powder wets out faster but can form lumps if it is dumped into acid all at once. The practical sequence is to disperse the powder in water first, then add the acid, or to sprinkle it into dilute acid while stirring.
Undissolved gel particles, sometimes called fish eyes, come from poor wetting rather than from insolubles. The certificate's insoluble-matter figure is measured on a properly dissolved sample, so it says nothing about lumps caused by the mixing technique.
Matching the grade to the dosage form
A capsule or tablet takes the 80 mesh powder. The fill meets gastric acid, where a high-deacetylation, low-viscosity lot dissolves readily and at higher solids than a thick grade would allow. In a tablet, a higher-viscosity lot can act as a binder at a low addition, but it also changes the disintegration time, so the choice belongs to the formulator rather than to the purchase order.
A powder blend is governed by flow, bulk density and segregation. Chitosan is light and can separate from denser actives in a V-blender or a sachet line; the particle-size line on the certificate and a bulk-density figure are the practical controls. A liquid or a concentrate needs a low-viscosity grade and a validated hold time, because the solution loses viscosity as it stands.
The quantity per serving is a formulation and labelling decision. This page describes grades; it does not set an intake.
What to write into the specification
- “Chitosan, CAS 9012-76-4, (C6H11NO4)n, source named.”
- “Degree of deacetylation ≥85% by titration, with the titration method named.”
- “Viscosity 50–200 mPa·s at 1% in 1% acetic acid, with temperature and standing time.”
- “Moisture ≤10.0%; ash ≤1.0%; insoluble matter ≤1.0%.”
- “Heavy metals and microbiology as listed; particle size ≥95% through 80 mesh.”
- “Food-grade route and allergen statement confirmed for the destination.”
When the catalog grade is the wrong choice
If the application needs a thickener, a film or a gel, the low-viscosity catalog grade is the wrong starting point: ask for a higher-viscosity lot and test it in the intended matrix. If the finished product has to avoid crustacean material, the source matters more than the deacetylation figure, and a fungal lot is a separate purchase with its own documents. A technical grade is not a cheaper food grade; it is a different specification with a different file.
The product hub carries the catalog specification; the level-four comparison sets chitosan against chitin; the COA page shows how each grade figure is reported; the glucosamine page covers the monomer that comes from the same shell; the quality page describes the release workflow.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation