Chitosan vs chitin: deacetylation, solubility and the specification
Chitin and chitosan are the same polymer at different stages of deacetylation. Chitin is the acetylated parent, insoluble in water and in dilute acid; chitosan is the partially deacetylated product whose free amine protonates in dilute acetic acid and dissolves. The boundary is a degree of deacetylation, not a trade name, and the specification has to carry the number, the method and the viscosity.
The difference between chitin and chitosan is a number — the share of units that lost their acetyl group — and that number decides solubility, viscosity and the specification.
Where chitin ends and chitosan begins
The two names describe a continuum, and the cut is a convention rather than a sharp chemical edge. Chitin is roughly the fully acetylated polymer, with only a small fraction of free amine; chitosan is the deacetylated product, and the practical boundary is usually placed near 50% deacetylation, where the polymer gains enough charge to dissolve in dilute acid. Commercial chitosan is sold well above that line, typically from about 70% to more than 95% deacetylated.
That range is wide enough to matter. A lot at 75% deacetylation and a lot at 90% are both called chitosan, and they differ in charge density, acid solubility, solution behaviour and the amount of acid needed to dissolve them. A purchase order that says “chitosan” without a deacetylation figure and a method has not specified which of them it wants.
The structural difference
| Property | Chitin | Chitosan |
|---|---|---|
| CAS number | 1398-61-4 | 9012-76-4 |
| Formula | (C8H13NO5)n | (C6H11NO4)n |
| Acetyl content | High; most units acetylated | Low; most units carry a free amine |
| Nitrogen | About 6.9% | About 8.4% at 85% deacetylation |
| Dilute acetic acid | Insoluble | Soluble |
| Water and alkali | Insoluble | Insoluble |
| Catalog specification | Not the material specified here | ≥85% deacetylated; 50–200 mPa·s |
The formula change is small per unit and large in effect. Removing an acetyl group takes away mass and leaves a free amine; the polymer loses about 42 mass units per converted unit, and the nitrogen percentage rises as the acetyl content falls. That arithmetic is why a nitrogen result can support or contradict a deacetylation claim.
Why one dissolves and the other does not
Chitosan dissolves because its free amine accepts a proton. In 1% acetic acid the pH is low enough that a large share of the amine groups are protonated, the polymer becomes a polycation, and the repulsion between charged chains plus the disruption of the inter-chain hydrogen bonds lets water in. Chitin has almost no free amine, so it stays neutral and heavily hydrogen-bonded, and water cannot separate the chains.
The same mechanism sets the limit. Raise the pH towards neutral and the amine deprotonates, the charge disappears and the polymer precipitates; that is why the catalog note says soluble in dilute acetic acid and insoluble in water and in neutral or alkaline solutions. In practice a 1% solution is prepared by dispersing the powder in water and adding the acid slowly, or by sprinkling the powder into dilute acid while stirring. Flakes hydrate slowly and usually need an overnight soak.
Solubility is also the quickest bench check that separates the two materials. A sample that dissolves to a clear or slightly hazy solution in 1% acetic acid is acting like chitosan; a sample that swells but does not dissolve is closer to chitin, whatever the label says.
The specification that separates them
For chitosan, the catalog specification is a set of numbers that describe both the deacetylation and the chain: degree of deacetylation ≥85% by titration, viscosity 50–200 mPa·s at 1% in 1% acetic acid, moisture ≤10.0%, ash ≤1.0%, insoluble matter ≤1.0% and ≥95% through 80 mesh, with the source named. The deacetylation figure without its method is not enough, because titration, NMR and FTIR can read the same lot a few points apart.
A chitin specification would carry a different set of lines, because the material is not bought for acid solubility. Quoting chitin against the chitosan sheet, or accepting a lightly deacetylated chitin as “chitosan”, produces a lot that fails at the first solution. The insoluble-matter line is the quiet safeguard here: an under-deacetylated fraction shows up there as well as in the titration.
The source belongs in the same specification. A shrimp, a crab and a fungal lot can all meet ≥85% deacetylation and still carry different allergen statements, ash levels and colour, and the buyer's regulatory team confirms the food-grade route for the destination.
Viscosity: the second number that defines the grade
Two lots at 85% deacetylation can behave like different materials if their chain lengths differ. Viscosity is the practical measure of that difference, and it is why the catalog grade fixes a range rather than a minimum. A 50–200 mPa·s lot dissolves to a workable solution at a few percent solids; a much thicker lot gels at the same concentration and traps air.
The two numbers are linked in production. The alkali treatment that raises deacetylation also shortens the chain, so a lot pushed to a higher deacetylation figure tends to arrive with a lower viscosity. A specification that fixes both tightly narrows the process window, and a supplier who claims both extremes without a method has probably measured them differently.
Which material to buy
Buy chitosan when the application needs an acid-soluble, film-forming or solution-stable polymer: capsules, tablets and powder blends in the supplement range, and the solutions behind them. Buy a higher-viscosity grade when the job is thickening or film strength, and a fungal-source grade when the crustacean allergen has to be avoided. A chitin enquiry is a different purchase with a different specification, and it should be quoted as such rather than supplied against the chitosan sheet.
The product hub carries the catalog specification; the grades page places this comparison in the wider range; the identity page gives the tests that separate the two polymers; the glucosamine page covers the monomer released when the chain is hydrolysed; the compliance page covers the source and allergen file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation