06 Identity & adulteration

How to prove a carnosine lot is L-carnosine

Technical document 06 · Reviewed 2026-11-19 · Carnosine

On this page
  1. Four separate questions
  2. Rotation, dilution and the zinc ratio
  3. What XRD adds
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Questions worth putting to the supplier

A lot is L-carnosine when the document, the chromatogram, the polarimeter and the mass balance agree. The document names the material, CAS 305-84-0 and C9H14N4O3. HPLC and IR show the dipeptide. Specific rotation within +20.0° to +22.0° on the dry basis shows the L-form. Assay, moisture and the impurity profile show that nothing else has been added or lost. A zinc result separates the dipeptide from zinc-carnosine.

In one line

A carnosine lot is proven by agreement: the chromatogram, the rotation and the moisture must all point to the same material.

Four separate questions

Each layer answers a question the others cannot. The document can be right while the powder is wrong; the chromatogram can show carnosine while the optical form is racemic; the assay can be in range while the impurity profile has moved. The table sets out what each test actually proves.

Four layers of L-carnosine identity
LayerWhat it asksMeasurementWhat the result supports
DocumentDoes the paper name the material?Name, CAS number, formulaOnly what the file says
ChromatographyIs the dipeptide carnosine?HPLC retention; IR spectrumThe molecule, not the form
Optical formIs it the L-form?Polarimetry on the dry basisThe stereochemistry
Mass balanceIs it diluted or hydrolysed?Assay, loss on drying, related substancesConsistency of the numbers

Rotation, dilution and the zinc ratio

Specific rotation is the observed angle divided by concentration and path length, corrected to the dried material. The L-form sits at +20.0° to +22.0°; the D-form turns the other way; a racemic mixture lands near zero. A low angle has two readings: a partly racemised lot, or a dilution, because the calculation uses the sample weight rather than the carnosine weight. The assay separates them. A normal assay with a low angle points to the optical composition; a low assay with a low angle points to a dilution.

Zinc gives a second ratio. The free dipeptide carries no zinc in its formula, while zinc-carnosine is 22.6% zinc and 19.3% nitrogen, against 24.8% nitrogen for L-carnosine. A zinc result near the chelate's figure is not a purity deviation; it is a different material.

What XRD adds

X-ray diffraction tells crystalline from amorphous and compares a pattern with a reference. It is useful when a lot looks different, when a supplier is new, or when a dilution is suspected. It does not measure optical purity or assay, and a “match” statement without the reference pattern and the detection limit is hard to assess.

On a disputed lot, XRD, rotation and HPLC answer different parts of the same question and are stronger together than any one alone. XRD is not a routine release test here. The XRD method note describes the measurement.

What adulteration looks like

Common L-carnosine substitutions and the signals
SubstituteEffect on the lotWhat to look forTest
D-carnosine or a racemateOpposite or reduced rotation; achiral assay may passRotation below +20.0° with an assay in rangePolarimetry
Zinc-carnosineAdds zinc; different moleculeZinc above trace levelICP-OES for zinc
DilutionLowers assay and specific rotation in proportionAssay low; rotation low; peak shape normalAssay, rotation and mass balance
MoistureHigher loss on drying; lower as-is assayLoss on drying above 1.0%Gravimetric loss on drying
Other dipeptideSimilar retention; different spectrumExtra peak or ratio shiftHPLC and IR; MS if needed

Appearance is a weak screen. A white powder can be carnosine, a dilution or something else entirely. The rotation, the zinc figure and the mass balance are the stronger checks; a certificate that reports only appearance and assay has not tested the most likely substitution.

How to write identity into the specification

  • “L-carnosine, CAS 305-84-0, C9H14N4O3, molecular weight 226.23.”
  • “Assay 98.0–101.0% by HPLC; state the basis.”
  • “Specific rotation +20.0° to +22.0° on the dry basis; report temperature, solvent and concentration.”
  • “Identification by IR and HPLC against the reference; loss on drying ≤1.0%.”
  • “Zinc below the agreed limit, to exclude zinc-carnosine.”
  • “Related substances, including free histidine, below the agreed limits.”
  • “Destination market and the material name settled before the first order.”

Questions worth putting to the supplier

  1. What material name and CAS number appear on this lot's certificate?
  2. Which temperature, solvent and concentration were used for the rotation?
  3. May I see the chromatogram and the IR spectrum, not only the assay figure?
  4. What zinc result did the lot return, and by which method?
  5. If we disagree, will you re-test the retained sample jointly?

Those five answers amount to an identity file; a single assay figure does not. The product page holds the catalog data; the COA page shows how those figures are reported for a lot; the grades page sets out the physical forms; the level-four comparison covers the chelate; the glutathione range is a second specialty ingredient whose forms are separate identities; the HPLC note explains the separation.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation