06 Identity & adulteration

How we prove an alpha-lipoic acid lot is the racemic grade

Technical document 06 · Reviewed 2026-11-19 · Alpha-Lipoic Acid

On this page
  1. The four identity layers
  2. The sulfur figure and the R:S ratio
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Six questions for the supplier

A racemic alpha-lipoic acid lot is confirmed by four agreeing lines: the document names the form and CAS number, infrared and HPLC identify the molecule, the melting point at 60–62 °C fits the racemic solid, and the assay, loss on drying and sulfur figure close the mass balance. The assay alone cannot separate the racemic grade from the R-form or from a dilution. A chiral test is the only direct evidence of optical composition.

In one line

Identity is four agreeing measurements: the document names the form, infrared and HPLC name the molecule, the melting point says which solid it is, and the mass balance says it has not been diluted.

The four identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of alpha-lipoic acid identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
InfraredAre the functional groups present?IR spectrum against a referenceThe molecule class, not the optical form
ChromatographyIs the main peak lipoic acid?HPLC retention and peak purityThe molecule, not the enantiomer
Melting pointIs it the racemic solid?Capillary melting rangeSolid form, within the other evidence
Mass balanceIs it diluted?Assay, loss on drying, sulfurConsistency of the numbers

Each layer answers a different question. One who supplies only the assay has measured the molecule without identifying the solid; one who supplies only the specification has not measured the lot at all.

The sulfur figure and the R:S ratio

Two ratios are useful for this material, one elemental and one optical. The elemental ratio is sulfur. The pure molecule is 31.08% sulfur by mass: two sulfur atoms at 32.06 each, divided by the molecular weight 206.33. A lot that assays at 99.0–101.0% by HPLC and reports sulfur close to 31.1% is consistent with the pure acid. A sulfur figure well below that points to a carrier or a dilution; a figure above it points to another sulfur species.

The optical ratio is R to S. Racemic material is about 1:1 and shows no net optical rotation; a single enantiomer rotates plane-polarised light and gives one peak on a chiral column. Neither the infrared spectrum nor the melting point replaces that measurement, because both can be consistent with the racemic solid while the optical composition is what the buyer is actually asking about.

X-ray diffraction: the solid-state check

X-ray diffraction answers the solid-state question: is the powder crystalline, and does the pattern match a reference? The racemic compound and a single enantiomer pack differently in the crystal, so their diffraction patterns are not the same, and XRD can support a form dispute that a melting point alone leaves open. It is not a purity assay and it does not measure the optical ratio.

XRD is not a routine release test for this product, and a certificate that reports “XRD conforms” without the pattern or the reference has added little. Ask for the reference pattern, the scan range and the detection limit before reading a match statement. For a disputed lot, XRD plus a chiral result plus the sulfur figure is stronger than any one of them.

What adulteration looks like

Common alpha-lipoic acid substitutions and the signals
AdulterantWhat it doesSignalTest
Racemic sold as R-ALANo optical rotation; wrong claimChiral ratio near 1:1; rotation near zeroChiral HPLC, polarimetry
Carrier or dilutionLowers assay and sulfurAssay low; sulfur below 31.1%Mass balance, elemental sulfur
Oxidised lipoic acidExtra peaks; colour and odour changePeak purity fails; assay lowHPLC, IR
Other disulfideSimilar sulfur chemistry, different retentionExtra peak; melting point offHPLC, melting point, MS
MoistureRaises loss on drying; lowers the as-is assayLOD high; dried assay normalLoss on drying

Colour is the weakest signal. Yellow crystalline powder covers a visible range, and a darker lot can be a drying problem rather than a substitution. The stronger signals are the melting point, the sulfur figure and the chiral result.

How to write the identity into the specification

  • “Racemic alpha-lipoic acid, CAS 1077-28-7, C8H14O2S2, molecular weight 206.33.”
  • “Assay 99.0–101.0% by HPLC; state the basis and the loss on drying.”
  • “Identification by infrared and HPLC; melting point 60–62 °C.”
  • “Loss on drying ≤0.5%; sulfur about 31.1% where the mass balance is required.”
  • “Particle size ≥95% through 40 mesh; heavy metals and microbiology as listed.”
  • “Optical form stated on the certificate; chiral result for any R-form claim.”

Six questions for the supplier

  1. Which optical form is this lot, and which CAS number is on the certificate?
  2. Can you provide the infrared spectrum and the HPLC chromatogram, not only the assay percentage?
  3. What melting range was measured, and what were the start and end temperatures?
  4. What is the loss on drying and the sulfur result for this lot?
  5. If the form is disputed, will you provide a chiral HPLC or polarimetry result?
  6. Will you accept a joint re-test on the retained sample?

Six direct answers amount to an identity file; a single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the forms; the level-four comparison covers the label consequences; the HPLC method note explains the separation.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation