03 Stability

Alpha-lipoic acid is light- and heat-sensitive; the pack sets the shelf life

Technical document 03 · Reviewed 2026-11-19 · Alpha-Lipoic Acid

On this page
  1. The powder: moisture, light and heat
  2. The solution: the least stable format
  3. What drives degradation
  4. A stability protocol for the ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

Racemic alpha-lipoic acid is sensitive to light and to heat, and its melting point of 60–62 °C is close enough to normal handling temperatures to matter. The sealed powder in a light-resistant pack is the most stable format; an aqueous or alcoholic solution is the least stable. Shelf life is assigned from stability data for the exact pack and storage condition, not from the certificate.

In one line

Light starts the damage, heat accelerates it, and a melting point of 60–62 °C puts the powder's physical limit closer to everyday warehouse temperatures than most ingredients.

The powder: moisture, light and heat

The catalog sets loss on drying at ≤0.5%. That is a release gate, not a storage allowance: once the foil pouch is open, the powder can pick up moisture from the air, the as-is assay falls and the powder begins to cake. The yellow colour can deepen, and the characteristic sulfurous note can become more pronounced as degradation products form. A dry store and a tight seal are part of the specification in practice even when they are not printed on the certificate.

Light is the second driver. The powder should stay in its original light-resistant pouch or in an opaque container that closes properly. A clear jar on a bench is not a storage container for this material, however convenient it looks. Heat is the third: at the top of a warehouse, in a loading bay or in a vehicle, the powder can approach its melting range, soften and sinter. A sintered powder fails its sieve result and may not disperse in the next process step.

The solution: the least stable format

The material is poorly soluble in water, which limits but does not remove the solution risk. Where a solution is needed, it is usually prepared in ethanol or in alkaline aqueous media, and both are less stable than the solid. Light, oxygen and pH act at once; the dithiolane ring and the carboxyl group are both involved, and the degradation products are not the starting material.

A ready-to-drink process adds a heat load through pasteurisation or hot fill that the powder never sees. If a liquid is unavoidable, protect it from light, control the pH, keep dissolved oxygen low and validate the hold time before filling. A bulk-powder stability result does not transfer to a beverage.

What drives degradation

Factors that move alpha-lipoic acid during storage
FactorWhat it doesControl
LightPhotodegradation; colour deepens and assay fallsFoil or opaque pack; dark store
HeatSoftening and caking near the melting range; faster degradationCool, shaded store; avoid hot vehicles
MoistureRaises loss on drying; lowers the as-is assay; cakingSealed pouch; desiccant where needed
OxygenOxidation at exposed surfaces and in solutionLow headspace; sealed pack; process control
pHSolution stability and solubility both changeValidate the matrix pH and the hold time
Metal ionsCatalyse sulfur chemistry and colour changeAvoid iron and copper contact

The factors are not independent. A warm, bright, humid store is worse than the sum of three separate effects, and an alkaline solution in clear glass combines several of them. The useful question is not whether alpha-lipoic acid is stable, but in which pack, at which condition and for how long.

A stability protocol for the ingredient

A useful protocol states the pack, the storage condition, the time points and the tests. Long-term storage at 25 °C/60% relative humidity and intermediate storage at 30 °C/65% relative humidity cover the warehouse; accelerated storage at 40 °C/75% relative humidity stresses the pack. A light-exposure arm covers the failure mode that a dark incubator misses, and it should follow a standard photostability design.

Test assay by HPLC, melting point, loss on drying, appearance, infrared identity and microbiology at each point. The melting point earns its place in the panel because a shift signals a change in the solid: moisture, a polymorph or a degradation product. The report should show the individual results and identify the pack and the lot family.

The finished formula changes the answer

A capsule or tablet has low water activity, but the shell and the excipients can still transfer moisture. Alkaline excipients, including some mineral salts, raise the pH at the particle surface and can change the local solubility and stability; check the fill's appearance and loss on drying after storage, not only at release. A granulated lot has a different surface area from the 40 mesh powder, so a stability file built on one does not automatically cover the other.

A gummy or a stick pack adds water activity, heat and light. A stick pack also depends on the seal: a pinhole is a failure, and the strip should be inspected, not only the powder. The formulator decides whether an overage is needed; that is a label and stability decision, and it does not repair a pack that lets moisture in.

How the shelf life is set

We do not publish a single shelf-life number for alpha-lipoic acid, because the pack and the storage condition set it. The assigned retest period belongs on the specification and is supported by the stability file for that pack. A number without a pack, a condition and a test panel is not a shelf life; it is a claim.

After the retest period, re-assay the retained sample before extending use. Do not extend by assumption, and do not carry a bulk figure to a repacked container. The product hub lists the standard packs; the COA page covers the release tests; the MOQ page covers pack and lead time; the HPLC note describes the assay; the quality page describes the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation