03 Stability

Alpha-ketoglutarate is hygroscopic, and its solution is unstable

Technical document 03 · Reviewed 2026-11-19 · Alpha-Ketoglutarate

On this page
  1. The powder: watch the water result
  2. The solution: the weakest format
  3. What shortens the life
  4. A protocol for the pack you will buy
  5. Capsules, sticks and drinks change the answer
  6. Assigning a retest period

α-Ketoglutaric acid picks up water from the air, and once it is dissolved it begins to change. The foil pouch and a dry weighing room protect the powder; a liquid needs its own hold time, measured in the real matrix. The retest period belongs to the pack and the storage condition, not to the name on the label.

In one line

Water shortens the powder's life and time in solution shortens the liquid's, so the pack, the seal and the validated hold carry the shelf life.

The powder: watch the water result

Karl Fischer water is capped at 1.0% at release. Passing that gate says nothing about the pouch a year later: the acid is hygroscopic, and every opening exchanges dry air for room air. The powder clumps, sticks to the scoop and gains mass, and the as-is assay slides downward although the dry acid has not changed.

Keep the pouch closed between weighings and keep the weighing room dry. A desiccant is useful in a humid climate but it cannot compensate for a fold-over closure. Let a cold pack reach room temperature before it is opened, so condensation does not settle on the powder.

Watch the colour and the texture. A white crystalline powder that turns cream, feels tacky or forms hard lumps has met water, and possibly heat. Re-drying a wet lot in an oven is not a repair: heat is part of the degradation route, and the lot needs a fresh assay before it can be used.

The solution: the weakest format

Dissolved in water, the keto acid is at its most vulnerable. In water the acid keeps reacting, and heat and pH both change the rate. A 5% solution reads 2.0–3.0, so a drink made with the acid is already acidic before any flavour system is added. A stock left on a bench for a shift is a hold that has to be measured, not assumed.

A stick pack sidesteps most of this because water is added at the point of use. A ready-to-drink product does not, and its stability has to be shown in the finished beverage, with the process heat load and the pack included. If a liquid is the only option, shorten the hold, fix the pH, keep oxygen low and keep iron and copper out of contact.

Bulk data cannot be pasted onto a drink formula. The matrix, the process and the pack each shift the loss rate.

What shortens the life

Factors that move α-ketoglutaric acid during storage
FactorWhat it doesControl
WaterRaises the water result; causes caking; dilutes the as-is assaySealed pouch; dry room; desiccant where needed
HeatSpeeds breakdown in solutionCool store; low process heat load
Time dissolvedLengthens exposure to water, oxygen and pHShort validated hold; point-of-use mixing
pHChanges the ionised form and the degradation rateFix and record the matrix pH
OxygenOxidises the keto acid in solutionLow headspace; deaeration where possible
Iron and copperCatalyse oxidation; shift the colourStainless or lined contact surfaces
MicrobesCan grow in an aqueous systemPreservative and process validation

These are not separate switches. A warm, humid store plus an open pouch is worse than either alone, and a clear tank at the wrong pH combines several at once. The question worth asking is not whether the acid is stable, but in which pack, at which condition and for how long.

A protocol for the pack you will buy

Write the study around the pack that will be sold. The warehouse arms are 25 °C/60% and 30 °C/65% relative humidity; the accelerated arm is 40 °C/75%. Add a solution arm at the intended pH and process temperature, because the powder chambers will never show what a beverage does.

Assay, water, pH, appearance and microbiology are measured at every pull. For a stick or a drink, repeat the panel in the matrix. Results should be listed one by one rather than compressed into “pass”, and the report should name the pack and the lot family.

Order the summary for the pack on the purchase order. A drum and a pouch differ in headspace and in how often they are opened, so data from one does not describe the other.

Capsules, sticks and drinks change the answer

A capsule or tablet has little free water, yet the shell and the excipients can still pass moisture into a hygroscopic fill. Check water and appearance at release and again at the end of the assigned period, and look at the fill for caking. In a stick pack, inspect the seal as well as the powder: a pinhole defeats the foil.

A beverage brings pH, heat, oxygen and time into the same container. Bulk data starts the answer but does not finish it. An overage is a label decision and a stability decision; it does not rescue a pack that leaks or a hold that is too long. D-ribose is another hygroscopic specialty powder, and it fails at the same place: the seal and the humidity of the room.

Assigning a retest period

A single shelf-life figure would mislead for this acid: the number belongs to a pack and a condition. The specification states a retest period that the stability file for that pack supports. A figure quoted without a pack, a condition and a test list is a marketing line.

Before extending use past the retest period, re-assay the retained sample. Extension needs a result, and a drum figure cannot be copied onto a repacked pouch. For the pack list see the product hub; for release tests the COA page; for pack and timing the MOQ page; the assay is in the HPLC note and the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation