03 Stability

Lactoferrin is heat-sensitive; the process and the pack decide the shelf life

Technical document 03 · Reviewed 2026-11-19 · Lactoferrin

On this page
  1. The dry powder
  2. In solution
  3. What actually moves the number
  4. The stability protocol
  5. What the formula and the process can do
  6. How the shelf life is set

Lactoferrin is a folded protein, and heat and water are what unfold it. A dry powder held at ≤5.0% moisture can keep its specification for the shelf life assigned to the pack; a solution that sees a pasteurisation step or a long hold at neutral pH is a different problem. The process and the pack decide the shelf life, not the certificate.

In one line

Lactoferrin fails through heat and moisture before it fails on the protein figure, so the pasteurisation step, the water activity and the pack barrier are what set the shelf life.

The dry powder

Spray-dried lactoferrin leaves the dryer as an amorphous powder at ≤5.0% moisture, and in that state the protein is protected by the glassy matrix around it. The reactions that age it are slow: moisture uptake, caking, a slow drift in colour, and a loss of solubility that appears before any change on the protein line. The 5.0% limit is a ceiling on the certificate rather than a target.

The powder is hygroscopic. An opened pouch in a warm room takes up water at the surface first, and the surface is where caking starts. A drum that has been opened and resealed several times can show lumps that were not there at release, and the certificate on the drum still describes the lot as it was packed. That is why the pack instructions and the storage condition belong in the stability file.

In solution

Lactoferrin dissolves in water to a clear to slightly hazy, pale pink solution, and the catalogue pH of 5.5–7.0 is measured on a 5% solution. In that range the protein is close to its most compact form and the iron is held on the binding sites. Heat above roughly 70 °C begins to unfold it; the exact point depends on pH, concentration, ionic strength and how much iron the protein carries.

pH moves the stability in two directions. Below about pH 4 the protein stays soluble but releases its iron, so a low-pH drink protects the clarity and not the iron load. Near the isoelectric point, which for lactoferrin is in the basic range, solubility falls and haze rises, so a neutral formulation is harder to hold clear than an acidic one. A long hold at neutral pH before filling is the quiet failure mode: no heat step, no visible change, and a haze that appears in the finished bottle.

Microbiology is the other limit on a solution. Lactoferrin is a protein and a nutrient, and a reconstituted tank is a good medium. The preservative system and the hold time are part of the stability question, not a separate quality topic.

What actually moves the number

Stability factors · what each one does and what controls it
FactorWhat it doesWhat controls it
HeatUnfolds the protein; loss of solubility and colourLower the temperature, shorten the hold, add after cool-down
MoistureCaking, browning, faster denaturation on later heating≤5.0% at packing, foil barrier, desiccant where needed
pHIron release below pH 4; haze near the isoelectric pointFormulate acidic or well away from the isoelectric point
Oxygen and lightColour fade and off-notes over monthsOpaque pack, nitrogen flush where the pack allows
ShearFoaming and surface denaturation at the air interfaceLow-shear transfer, keep the tank covered
Metal ionsCompetes for the binding sites and shifts the iron figureStainless steel contact, check the water and the other ingredients

The order matters: a powder that has picked up moisture survives the following heat step less well, so the moisture limit protects heat tolerance as well as flow.

The stability protocol

A stability file for lactoferrin has three parts. The first is real time: the powder in its commercial pack at 25 °C and 60% relative humidity, tested at the start and at intervals through the assigned shelf life. The second is accelerated: the same pack at 40 °C and 75% relative humidity for six months, used to rank formulations and to catch a failing pack early. The third is a process challenge: the solution held at the real pasteurisation temperature for the real hold time, plus the reconstituted hold at the real pH.

The test panel should follow the certificate: appearance, moisture, protein, iron saturation, pH, solubility and microbiology, with the iron figure included because a heat step can change the saturation reading even when the protein line holds. Colour belongs on the panel as a measured value or at least as a photograph against a standard, because the eye catches a drift that the other tests miss.

Accelerated data does not replace real-time data. It can support a launch and it can justify a shorter shelf life, but the date on the lot has to rest on the pack that was actually tested. A stability file built on a 1 kg pouch does not automatically cover a 25 kg drum, because the drum has a different surface-to-volume ratio and a different opening history.

What the formula and the process can do

The first decision is where the lactoferrin goes into the process. Adding it after the heat step and after cool-down removes the heat load entirely, and it is the simplest change available. If the process cannot move, a saturated grade is the more heat-tolerant form of the same protein, and the grade page sets out what that switch changes.

Granulation is a wet process followed by drying, so it adds a moisture cycle. A granulated grade can improve flow, but the granulation has to be validated on the protein, not only on the particle size. A direct-compression route with a fine milled powder avoids the water altogether and is often the simpler answer for a tablet.

The pack is the last control and the one most often specified by habit. A 1 kg aluminium foil pouch is a strong moisture barrier; a 25 kg fiber drum protects the pouches inside it rather than the powder directly. The MOQ and packaging page describes the pack options, and the loss on drying entry explains how the moisture figure is obtained.

How the shelf life is set

The shelf life is assigned to a pack, a grade and a storage condition, and it is supported by the stability file for that combination. There is no single number that applies to every lactoferrin pack, and a supplier who quotes one without naming the pack has not answered the question. Ask for the pack, the grade, the storage condition and the test panel behind the date.

After opening, the clock changes. The pouch has to be resealed or the powder transferred to a dry container, and the opened material is normally given a shorter working life than the sealed pack. The COA page shows which figures are re-checked at release, and the quality page describes how the retained sample supports a shelf-life claim after the fact.

The catalogue ranges are on the product page. For the effect of the iron band on heat behaviour, see iron saturation in lactoferrin.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation