01 COA & batch testing

What the COA for lactoferrin actually contains

Technical document 01 · Reviewed 2026-11-19 · Lactoferrin

On this page
  1. What the certificate lists
  2. The basis behind the protein and the iron figure
  3. Catalogue range, release limit and what a lot reports
  4. What moves between lots
  5. When an outside test earns its place
  6. What to compare between suppliers

A certificate for lactoferrin has to answer two questions a protein figure cannot: what the protein is, and how much iron it carries. The catalogue sets protein at ≥95.0%, iron saturation at 9.0–20.0%, moisture ≤5.0% and ash ≤1.5%, with identity by HPLC and ELISA. The batch COA confirms those figures for the lot that ships.

In one line

A lactoferrin certificate is comparable only when the protein figure, the iron saturation and the identity tests each carry their method and their basis, and the lot number ties them to the drum.

What the certificate lists

The parameter list is short because the material is one protein rather than a family of related extracts. The certificate describes the powder, identifies the protein twice, and reports the composition around it. The table lists the catalogue parameters; each lot certificate prints the agreed limits again.

COA parameter list · bovine lactoferrin, spray-dried, 80 mesh
ParameterMethodRelease limit
AppearanceVisualPinkish-white to light tan powder
IdentificationHPLC retention and ELISAConforms to reference
ProteinKjeldahl, factor stated≥95.0%
Iron saturationIron by ICP, calculated against binding capacity9.0–20.0%
Moisture and ashLoss on drying; gravimetric, furnace≤5.0%; ≤1.5%
pH (5% solution)Potentiometry5.5–7.0
Particle sizeSieve≥95% through 80 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent

CAS 112163-33-4 identifies the glycoprotein, not the grade. The same number covers a low-iron powder and a saturated one, so the CAS is a starting point for identity, not a substitute for the iron figure. The species and the milk source belong on the certificate as words, because a transferrin from another species would share much of the chemistry and none of the label position.

The basis behind the protein and the iron figure

Kjeldahl returns nitrogen, then a factor converts it to protein. That factor is an agreed convention, not a measurement, and the certificate should print it together with the basis: as-is or dry. At the 5.0% moisture limit, a 95.0% dry-basis figure is about 90.3% on an as-is basis, so a specification that omits the basis leaves a five-point gap open.

Peak-area purity is a third figure. An HPLC chromatogram can report the lactoferrin peak as 98% of total area while the nitrogen figure is 95%: one describes the ultraviolet signal in the main peak, the other the nitrogen the powder carries. Neither is wrong, and neither replaces the other.

Iron saturation is the iron measured in the powder divided by the iron the protein could bind at full occupancy. Bovine lactoferrin binds two ferric ions per molecule of about 80 kDa, which puts full occupancy at roughly 1.4 mg of iron per gram of protein. The 9.0–20.0% band therefore spans about 0.13–0.28 mg of iron per gram. A percentage without the iron method and the capacity assumption cannot be recalculated.

The denominator has to come from the same powder as the iron. If the protein is on a dry basis and the iron is not, the saturation shifts by the moisture content, and a purity figure swapped in for the protein figure moves it further.

Catalogue range, release limit and what a lot reports

The limit is the boundary a lot has to meet; the result is the value the laboratory found. A certificate that shows only one of the two leaves the buyer unable to check the other. “Conforms to specification”, with no number beside it, is an assertion rather than evidence.

Some parameters describe the process rather than the purity. The pH of a 5% solution reflects the counter-ion and the residual milk salts, and the 80 mesh figure describes the milling: ≥95% through 80 mesh means particles mostly below about 177 µm, with a coarse tail that affects flow more than chemistry.

What this page describes is the catalogue specification: the target the material is expected to hit. The COA that travels with a drum is the record for that drum. This site does not publish lot results, lot numbers or customer names.

What moves between lots

Iron saturation is the figure that moves most. It follows the iron load of the milk, the loading or stripping step the supplier applies, and the capacity assumption in the calculation. A lot at the bottom of the band and one at the top can both be released, and they will not look the same in a clear capsule: the more saturated powder is the deeper pink.

Protein follows the isolation and the dryer. A lot can pass the nitrogen figure and still disperse more slowly than the approved sample if it has seen more heat. Moisture follows the dryer and the pack, and the 5.0% limit is a ceiling rather than a target. Colour and odour are the least quantitative signals and often the most useful: a lot that has seen more heat darkens and picks up a cooked note while the certificate still passes.

When an outside test earns its place

An independent test earns its place when the source has changed, when a first commercial lot is heading into a regulated market, or when the label rests on a figure the supplier's certificate does not establish. The panel worth ordering is narrower than the certificate: iron by ICP-OES or ICP-MS for the saturation calculation, HPLC against a reference standard, a species-specific ELISA, protein by Kjeldahl with the factor stated, and ICP-MS for the contaminants, all on one sample.

A dispute is settled the same way. Send the retained sample, the certificate and the agreed specification to an independent laboratory, and ask for the tests that distinguish the possible explanations. The quality page explains how the batch file is stored with the retained sample.

What to compare between suppliers

Six lines belong side by side before anything else is compared: the identity method and its standard, the protein figure with its factor and basis, the iron saturation with its iron method and capacity assumption, the moisture and ash limits, the declared species and milk source with the allergen statement, and the mesh and pack. Two quotations that match on protein but diverge on the other five are describing different materials.

Behind the certificate sits a record: the site that made the lot, the milk stream that went in, the drying and milling conditions, and the retained sample. A certificate can be truthful and still belong to a different drum. The number on the COA, the pouch and the retained sample has to be one number.

The catalogue ranges sit on the lactoferrin product page; the iron-band choice is set out on the grade comparison page, the proof tests on the identity page, and the term itself in the COA glossary entry. The method is described in the HPLC method note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation