02.1 Iron saturation

Iron saturation in lactoferrin: what the percentage changes

Technical document 02.1 · Reviewed 2026-11-19 · Lactoferrin

On this page
  1. What the percentage means
  2. How the figure is measured
  3. What the percentage changes
  4. How the grade is made
  5. What it means for the label
  6. When to choose which

Iron saturation is the share of lactoferrin's iron-binding sites that carry iron. At about 80 kDa with two binding sites per molecule, full occupancy is roughly 1.4 mg of iron per gram of protein, so the catalogue band of 9.0–20.0% corresponds to about 0.13–0.28 mg of iron per gram. The percentage changes the colour, the iron contributed per gram and the heat behaviour of the powder.

In one line

Iron saturation is the share of the protein's binding sites that carry iron, and it changes the colour, the iron per gram and the heat behaviour before it changes the protein figure.

What the percentage means

The figure is a ratio with no unit: iron found on the protein divided by the iron the protein could hold at full occupancy, expressed as a percentage. The numerator is an iron measurement. The denominator is a calculation from the protein figure, the molecular mass and the number of binding sites. Neither part is read directly from the powder, and a certificate that gives only the percentage has given a result without its arithmetic.

The mass matters because the protein is large. Bovine lactoferrin is about 80 kDa and binds two ferric ions, so one gram of pure protein carries about 1.4 mg of iron when every site is filled. At 100% saturation the powder would be 0.14% iron by mass, which is why a fully saturated grade is still a protein product rather than an iron supplement. The catalogue band sits at roughly a tenth to a fifth of that load.

The basis matters as much as the mass. Saturation calculated against protein on a dry basis and saturation calculated against the same protein on an as-is basis differ by the moisture content. The 5.0% moisture limit moves the figure by a few tenths of a point: small beside the band, not beside a claim that a lot sits at a precise number.

How the figure is measured

The iron is measured first, usually by ICP-OES or ICP-MS after digestion. The result is reported as mg of iron per kg of powder or per gram of protein. The saturation is then calculated from the protein figure, the assumed molecular mass and the two binding sites. Two laboratories can measure the same powder and report different saturations if they assume different binding capacities or use different protein bases.

The protein figure behind the calculation has to be the same one printed on the certificate. If the iron is measured on the powder as received and the protein is a dry-basis figure, the ratio carries the moisture difference. If the protein is a peak-area purity rather than a Kjeldahl figure, the denominator describes a different quantity. Ask for the calculation, not only the result.

Measured iron includes iron that is not on the protein, from residual salts or a contaminant. The calculation counts all of it as bound, which is one reason the percentage needs its method and its tolerance. A thorough method digests the whole sample and reports total iron.

What the percentage changes

Iron saturation · what moves with the band
PropertyLow saturationHigh saturation
ColourPaler pink to off-whiteDeeper pink to light tan
Iron per gram of proteinToward zeroToward about 1.4 mg
Heat behaviourUnfolds at a lower temperatureMore resistant to heat
Solution colourFaint pinkStronger pink; check haze
Certificate lineOwn upper limitOwn lower limit

The colour difference is visible in a clear capsule and in a pale drink, and it is the first thing a buyer notices when a grade changes. The heat difference is the first thing the process notices: the iron-free form of the protein is less stable, so a low-iron grade put through the same pasteurisation step as a saturated grade will lose solubility sooner. Neither difference is a change in the protein figure, which is why a certificate can look unchanged while the powder behaves differently.

Solubility is the property most often assumed to be constant and least often checked. Both forms dissolve, but the saturated powder carries more colour into the solution and can show more haze at the same concentration. A grade switch should be followed by a clarity check in the real matrix, not only by a certificate review.

How the grade is made

Bovine lactoferrin is isolated from milk or the whey stream, usually by a chromatography step that takes advantage of the protein's basic charge. The iron load that arrives with the raw material is the starting point. A low-iron grade is made by stripping iron from the protein, typically at low pH with a chelating agent, and then removing the agent and drying the protein. A saturated grade is made by loading ferric iron onto the binding sites before drying.

Both steps change the powder and neither changes the protein sequence. The process is part of the grade definition, because a supplier who strips iron and one who loads it are selling different specifications from the same starting material. The process belongs in the supplier file, and a change of process is a change of grade even when the certificate band looks similar.

What it means for the label

The iron carried by the protein is part of the ingredient rather than an added nutrient, but the quantity is calculable and a product that makes an iron statement should show the arithmetic. One hundred milligrams of powder at 95% protein and 20% saturation carries about 0.03 mg of iron, roughly 0.2% of the 14 mg EU reference intake for iron. The same mass at full saturation would carry about 0.13 mg, just under 1%.

Those figures explain why lactoferrin is not usually a meaningful iron source on the label, and why a saturated grade does not turn a protein ingredient into an iron supplement. The grade name still belongs on the specification and, where the label builds a story on it, on the pack. “Iron saturation” is a specification term, not a standardised label term in every market, so the number has to be defined where it is used.

When to choose which

Choose the catalogue band for a dry blend or a capsule with no hot step, no iron statement and a pack that keeps moisture out. It is the widest specification and the least likely to need a new stability file. Choose a low-iron grade when the palest colour matters, when the iron contribution has to stay at the bottom of the range, or when the process is mild enough that the lower heat tolerance is not a risk. Choose a saturated grade when the process includes a heat step that cannot be moved, or when the deeper colour is the point of the product.

The decision is a specification decision, and it should be written into the purchase order with its limit and its method. The grade comparison page sets out what else changes with the grade, the stability page covers the heat and moisture side, and the COA page shows how the figure appears on the certificate. The catalogue ranges are on the product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation