06 Identity & adulteration

How we prove a colostrum lot is colostrum

Technical document 06 · Reviewed 2026-11-19 · Colostrum

On this page
  1. The four layers
  2. The ratio that has to agree
  3. What diffraction and infrared can add
  4. The routes that are actually used
  5. What to write into the specification
  6. Five questions for a supplier

A colostrum lot is identified by measurements that have to agree: IgG by radial immunodiffusion, protein by Kjeldahl with its factor, fat and lactose, and the ratios between them. The ratios are the part that catches a substitution, because a milk powder can be pushed towards a protein figure but not towards a colostrum IgG profile.

In one line

Identity is the ratio, not a single figure: IgG at 20% of the powder and about 29% of the protein, with lactose under 5%, is a colostrum profile that milk powder cannot copy.

The four layers

The first layer is the IgG result. Radial immunodiffusion against a bovine IgG standard gives a precipitation ring whose diameter is read from a curve, and the figure is specific to the immunoglobulin rather than to protein in general. It is also the layer a blender finds hardest to fake, because a low-IgG powder can only be lifted by adding an IgG source.

The second layer is the protein figure with its method and its factor. Kjeldahl nitrogen × 6.38 is the dairy convention; a certificate that omits the factor has not defined the number. The protein figure also has to be read against the IgG figure, because the two are not independent.

The third layer is the fat and lactose pair. Skimming sets the fat and a lactose-reduction or ultrafiltration step sets the lactose, and the pair is what separates a colostrum powder from a milk powder at a glance: mature milk powders carry much more lactose than this specification allows.

The fourth layer is the description and the source: off-white to light tan powder, a slightly turbid solution, a declared bovine origin and a collection window. None of those is a test, but each one narrows the field before the laboratory work starts.

The ratio that has to agree

At the catalog limits, IgG is 20.0% of the powder and about 29% of the protein. That ratio is the identity signature. IgG is itself a protein, so the two figures cannot both be high without the ratio holding: a certificate that reports 70% protein and 2% IgG describes a milk protein, not colostrum.

Mature bovine milk carries IgG at well under 1% of its protein, and a skim milk powder dried from it stays in that range. A blend of colostrum with skim milk powder moves the ratio down and the lactose up, and the two moves are visible on the same certificate. Read the ratio and the lactose together rather than trusting the protein figure on its own.

The fat figure adds a third check. Whole milk powder holds roughly a quarter of its mass as fat and about 38% as lactose; skim milk powder trades the fat for lactose and lands near 50%. Colostrum powder at fat ≤5.0% and lactose ≤5.0% is nowhere near either, so a lot that reads like a milk powder is a milk powder however the label reads.

Season and parity move the raw ratio, which is why the specification is written to a floor rather than to a typical value. A blend that meets the IgG floor while the protein sits at the top of the range is a legitimate lot with a high ratio, and it should not be rejected for being better than the minimum.

What diffraction and infrared can add

Spray-dried colostrum has no crystal lattice, so an X-ray diffraction scan returns one broad hump and no reflections. The flat pattern is a sign the process did what it should: sharp peaks would mean a crystalline phase, and here the usual candidate is crystalline lactose from a permeate or a whey-derived diluent rather than the protein.

Infrared spectroscopy shows the protein backbone in the amide I and amide II regions and confirms that the powder is protein-rich rather than a carbohydrate or a salt. The carbohydrate region between roughly 1,000 and 1,100 cm⁻¹ is the useful part for adulteration: a strong band there points to lactose, maltodextrin or sucrose that the fat and lactose figures should already have flagged. The FTIR note and the XRD note describe what each technique can settle, and the methods index lists the rest.

The routes that are actually used

Adulteration routes for colostrum powder · the signal and the test
RouteWhat it changesTest that catches it
Skim or whole milk powder addedLactose climbs to 35–50%, IgG falls below 1% of proteinLactose, IgG-to-protein ratio
Whey or permeate powderProtein drops, lactose climbs, IgG is lowLactose, protein, IgG
Maltodextrin or starchProtein and IgG fall together; carbohydrate bands appearProtein, IgG, FTIR, moisture
Non-protein nitrogenKjeldahl rises, IgG does notNitrogen against IgG, melamine screen
Colostrum of another speciesChromatogram and ring may be close; origin document is the tellSpecies-specific antibody, origin record
IgG from a non-colostrum sourceHigh IgG without the colostrum fat and lactose profileRatio, fat, lactose, process record
Lower grade re-labelledCertificate and pack disagree on the IgG figureLot trace, retained sample

Most of these routes are substitutions rather than safety events: a different milk protein or a carrier sold as the declared article. The nitrogen route is the safety one, and it is the reason a protein figure without an IgG figure is weak evidence for this material. The grade page explains why the IgG figure is a grade parameter as well as an identity check.

What to write into the specification

  1. The name, source and species: bovine colostrum powder, with the collection window stated.
  2. IgG ≥20.0% by radial immunodiffusion, with the standard named and the sample preparation described.
  3. Protein ≥70.0% by Kjeldahl with the factor 6.38 printed beside it.
  4. Fat ≤5.0% and lactose ≤5.0%, which together carry much of the identity evidence.
  5. Moisture, particle size, heavy metals and microbiology as release limits.
  6. The milk allergen and bovine origin declarations, and the process temperature.

Strip out the IgG method and the protein factor, and the document describes a protein powder with no evidence of its source. The product page carries the catalog ranges that a specification starts from, and the COA page shows how each figure reaches the certificate.

Five questions for a supplier

  1. Which IgG method and which reference standard were used, and can you send the standard curve for the lot?
  2. Which nitrogen factor is printed beside the protein figure?
  3. How soon after calving was the raw colostrum collected, and is the window stated on the specification?
  4. What are the fat and lactose figures for the lot, and do they match the ratio on the certificate?
  5. Which lot number links the retained sample to the pouch, the drum and the COA?

These are ordinary questions for this material; an answer that cannot be given is a powder without the evidence behind it. The quality page sets out how the retained sample and the release file are kept.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation